Loctite-Permatex 24283 Adhesives & SealantsMedium Strength Threadlocker Blue - 90ml BottleOEM specified. All-purpose, medium strength threadlocker. Ideal for all nut and bolt applications 1/4″ to 3/4″ (6mm to 20mm). Eliminates need for stocking expensive lock nuts and lock washers. Locks and seals while preventing parts loosening due to vibration. Protects threads from corrosion. Removable with hand tools for easy disassembly. Conforms to ASTM D 5363 AN0321 (Mil-S-46163A, Type II, Grade N). Applications: Automobile- Suggested Applications: Valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts, carburetor studs Motorcycle - Suggested Applications: Handlebar brackets, mirror fixtures, shock bolts, rear fender nuts, small fastener nuts Heavy Duty - Suggested Applications: Case cover bolts, axle housing bolts, oil seal retainer bolts, axle shaft flange bolts, differential drain plugs, fuel tank fasteners, lug nuts, windshield wiper nuts, gear shift knobs, door hardware, running light screws, horning mounting Marine - Suggested Applications: Valve cover bolts, water pump bolts, oil pan bolts, drive shaft bolts, rocker arm adjustment nuts, carburetor studs Directions: Clean and dry parts using Permatex® Surface Prep™ activator. Shake tube of Medium Strength Threadlocker well before each use. Remove cap and snip nozzle tip. Apply Medium Strength Threadlocker to threaded areas and assemble parts. Refer to Technical Data Sheet for complete information. NOTE: Medium Strength Threadlocker works on metal parts. It is not recommended for plastics. Cured Medium Strength Threadlocker must be sheared (hand tools will do) before parts will separate. Normalized SKU: 24283UPC Code: 686226242839

Loctite-Permatex 77164 Adhesives & SealantsNickel Anti-Seize Lubricant Brush Top Bottle - 16ozProtects metal parts from seizing and galling at temperatures up to 2400°F (1316°C). It is recommended where copper contamination must be avoided, under conditions of extreme pressure and temperature, and with stainless steel, titanium and nickel alloys. Applications:Automobile - Suggested Applications: Exhaust manifold bolts, exhaust system bolts, muffler clamps and tailpipe assemblies.Directions:STIR WELL BEFORE USING. For best results, remove dirt, oil and grease. Apply Anti-Seize lubricant to parts that require protection. Wipe away excess lubricant. Refer to Technical Data Sheet for additional information. Normalized SKU: 77164UPC Code: 686226771643

Loctite-Permatex 77124 Adhesives & SealantsNickel Anti-Seize Lubricant Brush Top Bottle - 8ozProtects metal parts from seizing and galling at temperatures up to 2400°F (1316°C). It is recommended where copper contamination must be avoided, under conditions of extreme pressure and temperature, and with stainless steel, titanium and nickel alloys. Applications:Automobile - Suggested Applications: Exhaust manifold bolts, exhaust system bolts, muffler clamps and tailpipe assemblies.Directions:STIR WELL BEFORE USING. For best results, remove dirt, oil and grease. Apply Anti-Seize lubricant to parts that require protection. Wipe away excess lubricant. Refer to Technical Data Sheet for additional information. Normalized SKU: 77124UPC Code: 686226771247

Loctite-Permatex 29040 Adhesives & SealantsPenetrating Grade Threadlocker GREEN Tube - 36mlOEM specified. A low viscosity threadlocking liquid that wicks along the threads of preassembled fasteners to secure them in place. Since it is applied after assembly, preventive maintenance procedures are simplified. Ideal for fasteners ranging from #2 to 1/2″ (2.2 to 12mm) in size. Localized heating and hand tools are needed for disassembly. Conforms to ASTM D5363 AN0261 (Mil-S-46163A, Type III, Grade R). Applications: Automobile - Suggested Applications: Bolts on alternators, air conditioning belts and distributor clamps, carburetor adjustment screws, and hairline cracks. Marine - Suggested Applications: Bolts on alternators, distributor clamps, carburetor adjustment screws, hairline or porosity cracks Directions: Clean and dry parts using Permatex® Surface Prep™ activator. Assemble parts and make adjustments. Apply Threadlocker where thread enters parts. Refer to Technical Data Sheet for complete information. NOTE: Threadlocker works on metal parts. It is not recommended for plastics. To disassemble parts, weaken cured Threadlocker by heating above 500°F (260°C); then use hand tools to separate components. Normalized SKU: 29040UPC Code: 686226290403

Loctite-Permatex 26210 Adhesives & SealantsPermanent Strength Threadlocker RED Tube - 10mlOEM specified. A permanent, high strength product that is applied to fasteners 3/8″ to 1″ (10mm to 25mm) in size before assembly. Designed for securing parts that must withstand heavy shock, vibration, or extreme chemical or environmental conditions. Localized heating and hand tools are required to separate parts. Conforms to ASTM D5363 AN0331 (Mil-S-46163A, Type II, Grade O). Applications:Automobile - Suggested Applications: Assembly with air tools, cylinder block bolts, ring gear bolts, transmission shaft boltsDirections: Clean and dry parts using Permatex® Surface Prep™activator. Shake tube of Threadlocker well before each use. Remove cap and snip nozzle tip. Apply Threadlocker to threaded areas and assemble parts.Refer to Technical Data Sheet for complete information. NOTE: Threadlocker works on metal parts. It is not recommended for plastics. Cured Threadlocker must be heated to 500°F (260°C) before parts will separate. Normalized SKU: 26210UPC Code: 686226262103

Loctite-Permatex 26250 Adhesives & SealantsPermanent Strength Threadlocker RED Bottle - 50mlOEM specified. A permanent, high strength product that is applied to fasteners 3/8" to 1" (10mm to 25mm) in size before assembly. Designed for securing parts that must withstand heavy shock, vibration, or extreme chemical or environmental conditions. Localized heating and hand tools are required to separate parts. Conforms to ASTM D5363 AN0331 (Mil-S-46163A, Type II, Grade O). Applications:Automobile - Suggested Applications: Assembly with air tools, cylinder block bolts, ring gear bolts, transmission shaft boltsDirections: Clean and dry parts using Permatex® Surface Prep™activator. Shake tube of Threadlocker well before each use. Remove cap and snip nozzle tip. Apply Threadlocker to threaded areas and assemble parts.Refer to Technical Data Sheet for complete information. NOTE: Threadlocker works on metal parts. It is not recommended for plastics. Cured Threadlocker must be heated to 500°F (260°C) before parts will separate. Normalized SKU: 26250UPC Code: 686226262509

Loctite-Permatex 84160 Adhesives & Sealants1 Minute General Purpose Gel Epoxy - .84ozGeneral Purpose 1 Minute Gel Epoxy is a fast setting, two-part adhesive and filler system specially formulated with a Blue Dye Indicator that disappears when it’s fully mixed and ready to use. The advanced gel formulation reduces mess and waste compared to traditional epoxies; unique indicator system takes the guesswork out of “ready to use”.Features: Non-drip formula allows for mess free application Can easily be applied to overhead and hard to reach places Sets in just 1 minute/Cures in 5 minutes Blue dye indicator disappears when epoxy is ready to apply No clamping required Bonds to metals, hard plastics, ceramics, and more! Applications:Automobile - Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including, ceramic, chrome, fabric, fiberglass, glass, hard plastic, and metal and rubber.Directions: PROTECT: Work area must be protected from accidental spills. CLEAN: Surfaces must be clean, dry and free of grease and oil. PREPARE: Roughen smooth surfaces (using abrasives or sandpaper). OPEN PACKAGE: Remove Syringe. Turn syringe nozzle end up and pull plunger back slightly (1/8”). Allow air bubbles to rise to top. Snap off and save storage cap. Push plunger to dispense equal amounts of hardener and resin onto discard-able surface such as a piece of cardboard. Mixing paddle will pop out from plunger. Pull back plunger tostop flow. Snap cap back on. MIX QUICKLY: Quickly and thoroughly mix until blue color turns clear (about 15 sec).  APPLICATION: Apply small amount of mixture to both surfaces and assemble parts immediately (product sets in approximately 60 seconds). Remove any excess epoxy immediately. CURE TIME: Usable strength is reached in 1 hour at 72ºF (22ºC).Cooler temperatures may require longer set time. CLEAN-UP: Attach nozzle cap and store in molded tray. NOTE: Adhesive will not bond most polyethylene or polypropylene plastics. Normalized SKU: 84160UPC Code: 686226841605

Loctite-Permatex 84209 Adhesives & SealantsSteel Weld™ Epoxy - GREY - 1ozVersatile, easy-to-use, multi-metal epoxy adhesive is two-part adhesive and filler system that eliminates the need for welding or brazing. Sets in four minutes, no clamping needed. Dark grey appearance. Fills gaps and will not shrink. When cured, can be drilled, sanded, threaded or filed. Resistant to water and solvents. Temperature range -60°F to 300°F (-51°C to 149°C). Permanent strength up to 4500 PSI. Applications:Automobile - Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including aluminum, brass, chrome, copper, iron, stainless steel, steel. Use to seal welded seams, fills metal cracks, mount metal components.Directions:1. PROTECT: Work area must be protected from accidental spills. 2. CLEAN: Surfaces must be clean, dryand free of grease and oil. 3. PREPARE: Roughen smooth surfaces (using abrasives or sandpaper). 4. OPENPACKAGE: Remove tubes and use a sharp point to puncture seals. 5. DISPENSE: Squeeze tubes to dispense resin andhardener. Thoroughly mix resin & hardener on a clean, discardable surface for 2 to 3 minutes until evenly colored.6. APPLICATION: Apply a small amount of mixture to both surfaces and assemble parts immediately (working time isapproximately 4-6 min.). Remove any excess epoxy immediately. 7. CURE TIME: Usable strength is reached in fourhours at 72°F (22°C). Cooler temperatures may require longer set time. 8. CLEAN-UP: Attach nozzle caps and store inmolded tray. NOTE: Adhesive will not bond most polyethylene or polypropylene plastics. Normalized SKU: 84209UPC Code: 686226842091

Loctite-Permatex 84201 Adhesives & Sealants5 Minute Gap Filling Epoxy - .6ozVersatile, easy-to-use, general purpose epoxy adhesive is two-part adhesive and filler system that eliminates the need for welding or brazing. Sets in five minutes, no clamping needed. Clear appearance. Fills gaps and will not shrink. Resistant to water and solvents. Temperature range -60°F to 180°F (-51°C to 82°C). Permanent strength up to 3400 PSI. Self-mixing dual syringe (84164) blends the adhesive and filler as it dispenses, eliminating the need for manual mixing.Applications:Automobile - Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including, ceramic, chrome, fabric, fiberglass, glass, hard plastic, metal and rubber.Directions: PROTECT: Work area must be protected from accidental spills. CLEAN: Surfaces must be clean, dry and free of grease and oil. PREPARE: Roughen smooth surfaces (using abrasives or sandpaper) OPEN PACKAGE: Remove tubes and use the back of cap or a sharp point to puncture seals. DISPENSE: Squeeze tubes to dispense resin and hardener. Thoroughly mix resin & hardener on a clean, discardable surface for 2 to 3 minutes until evenly colored. APPLICATION: Apply a small amount of mixture to both surfaces and assemble parts immediately (product sets in 4-6 minutes).Remove any excess epoxy immediately. CURE TIME: Usable strength is reached in four hours at72°F (22°C). Cooler temperatures may require longer set time. CLEAN-UP: Attach nozzle caps and store in molded tray. NOTE: Adhesive will not bond most polyethylene or polypropylene plastics. Normalized SKU: 84201UPC Code: 686226842015

Loctite-Permatex 71500 ShopSpray Nine Poly 500® Hand Cleaner Revolution Dispenser for Grease GrabberGet “pennies per wash” economy out of your Grease Grabber® or Spray Nine®. The Poly 500™ metered dispensing system delivers the perfect amount of hand cleaner every time! The Poly 500™ can be mounted and features a lockable lid. Installation Instructions: Place lid on dispenser and line up preformed holes. Insert metal ring (provided) through holes on either side. The opposite side may be locked with a padlock if desired. For Best Results: Install dispenser to properly secured mounting board using the (4) 1 inch screws provided. If mounting onto concrete wall, plastic screw anchors or all-purpose masonry anchors are recommended. Mounting the dispenser onto hollow drywall is not recommended. If necessary, however, toggle bolts or other appropriate anchoring devices should be used. Loading Instructions: Raise dispenser lid. Place open 4 lb container upside down into dispenser. Carefully puncture bottom of container where indicated for proper venting. Slowly lift and squeeze container to evacuate product. Dispenser may also be manually filled from 26 lb pail (Poly Scrub #13126, Coco Scrub #14126). Normalized SKU: 71500UPC Code: 077174002864

Loctite-Permatex 85913 Adhesives & SealantsClear RTV Silicone Adhesive Sealant - 7.25ozGeneral-purpose, clear RTV indoor/outdoor sealant. Seals, bonds, repairs, mends and secures glass, metal, plastics, fabric, vinyl, weather stripping and vinyl tops. May be applied to horizontal or vertical surfaces. Waterproof and flexible. Temperature range -75°F to 400°F (-59°C to 204°C); resists oil, water, weather, vibration, grease. Applications: Automobile - Suggested Applications: Door frames, vinyl tops, seams and roofs (Not recommended for engine gasket or electrical connection applications). Heavy Duty - Suggested Applications: Windshields Marine - Suggested Applications: Windshields, hatches, seams and roofs Directions:Surfaces should be clean and dry. Apply silicone with a continuous,uniform flow. Bead size may be varied by finger pressure, how quickly applicator is moved and angle. For heavier beads,nozzle may be cut to size. Activate PowerBead™ by twisting nozzle one full turn counterclockwise, raising trigger. Press trigger to dispense. Assemble parts immediately while silicone is still wet. Surfaces being bonded may require clamping until silicone is firm. Silicone“skins” and becomes tack-free in one hour. Allow 24 hours for full cure under normal conditions, longer in cold or dry conditions.After use, store applicator by twisting nozzle clockwise, wiping away excess silicone and replacing plastic cap with a “click”. Normalized SKU: 85913UPC Code: 686226859136

Loctite-Permatex 85915 Adhesives & SealantsHigh-Temp Red RTV Silicone Gasket - 7.25ozOEM specified. Formulated for hi-temp applications, or heavy-duty use (such as towing, etc.). Replaces almost any cut gasket by making reliable “formed-in-place” gaskets that resist cracking, shrinking and migrating caused by thermal cycling. Coats pre-cut gaskets to increase reliability. Temperature range -65ºF to 650ºF (-54°C to 343°C) intermittent; resists auto and shop fluids. Applications:Automobile - Suggested Applications: Valve covers, oil pans, timing covers, thermostat housingsDirections:Surfaces should be clean & dry. Apply a continuous, uniform 1/16” to 1/4” bead of silicone, surrounding all bolt holes. 1/8” is suitable for most applications. Bead size may be varied by finger pressure, how quickly applicator is moved and angle. For heavier beads, nozzle may be cut to size. Activate PowerBead™ by twisting nozzle one full turn counterclockwise, raising trigger. Press trigger to dispense. Assemble parts immediately while silicone is still wet. Silicone will fully cure in 24 hours. After use, store applicator by twisting nozzle clockwise, wiping away excess silicone & replacing plastic cap with a “click”.NOTE: Not recommended for use on head gaskets or parts in contact with gasoline. Normalized SKU: 85915UPC Code: 686226859150

Loctite-Permatex 85224 Adhesives & SealantsPowerbread The Right Stuff® Instant Gasket Maker - Black - 7.5ozMake leak-proof gaskets and return equipment to service immediately! Permatex premier instant gasket maker was designed as a replacement for conventional gaskets. This elastomeric “formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. Formulated to meet or exceed performance standards for long-term salability, durability and handling, this material is used on OEM production lines and specified in their service parts programs. Temperature range -75°F to 450°F (-59°C to 232°C) continuous, 500°F (260°C) intermittent; resists ATF, coolant, oil and other shop fluids. Sensor-safe. Compared to Permatex® the Right Stuff® GREY Gasket Maker, our Black formula offers higher oil resistance and retains greater flexibility. This makes it best for older, higher displacement engines. Applications:Automobile - Suggested Applications: Automotive, heavy duty, and marine gaskets, valve covers, gearbox covers, pumps, oil pans, thermostat housings, water pumps.Motorcycle - Suggested Applications: Transmission housing cover, clutch release coverHeavy Duty - Suggested Applications: Case covers, power divider shaft housings, input/output power shafts, PTO covers to housing, cover housing gasket, differential, assembly to rear axle housing, power dividers, axle shaft flangesDirections:Clean and dry parts. Push nozzle to dispense the Right Stuff®. Apply a continuous 1/8″ to 1/4″ bead to one surface, surrounding all bolt holes. Assemble parts within five minutes, tightening bolts to recommended torque levels. Material will fill any surface imperfection. Equipment can be returned to service immediately. To reuse package, leave a 1/2″ length of material extending out of the nozzle. Cured material will form a protective plug. To reuse, carefully remove the plug and dispense as before.NOTE: Not for use as a head gasket or on parts in contact with gasoline. Normalized SKU: 85224UPC Code: 686226852243

Loctite-Permatex 85519 Adhesives & SealantsUltra Blue® Multipurpose RTV Silicone Gasket Maker - 7.5ozOEM specified. Designed specially for high-torque and high vibration applications, like those common in import engines, this premium RTV gasket maker exceeds manufacturer performance requirements. Sensorsafe, low odor, and noncorrosive. Maximum vibration resistance, with outstanding resistance to oils, cooling and shop fluids. Guaranteed not to leak. Temperature range -65ºF to 500ºF (-54°C to 260°C) intermittent. Applications: Automobile - Suggested Applications: Valve covers, oil pans, and timing covers. Marine - Suggested Applications: Valve covers, oil pans, intake manifold end seals, timing covers, water pumps, thermostat housings Directions:Surfaces should be clean & dry. Activate PowerBead™ by twisting nozzle one full turn counterclockwise, raising trigger. Press trigger to dispense. Apply a continuous, uniform 1/16” to 1/4” bead of silicone, surrounding all bolt holes. 1/8” is suitable for most applications. Bead size may be varied by finger pressure, how quickly applicator is moved and angle. For heavier beads, nozzle may be cut to size. Assemble parts immediately. Finger tighten bolts until material begins to squeeze out around flange. Allow to dry for 1 hour then retighten 1/4 to 1/2 turn. Silicone will fully cure in 24 hours. After use, store applicator by twisting nozzle clockwise, wiping away excess silicone & replacing plastic cap with a “click”.NOTE: Not recommended for use on head gaskets or parts in contact with gasoline. Normalized SKU: 85519UPC Code: 686226855190

Loctite-Permatex 85084 Adhesives & SealantsUltra Grey® Rigid High-Torque RTV Silicone Gasket Maker - 9.5ozOEM specified. Permatex® Ultra silicones were developed to meet today's technology changes. Sensor-safe, low odor, noncorrosive. Outstanding oil resistance and joint movement tolerance. Eight times more flexible than cork/composite gaskets; three times more oil resistant than conventional silicones. Temperature range -65ºF to 500ºF (-54°C to 260°C) intermittent; resists auto and shop fluids and vibration. Applications: Automobile - Suggested Applications: Valve covers, oil pans, automatic transmission pans, intake manifold end seals, timing covers, water pumps, thermostat housings Heavy Duty - Suggested Applications: Cover housing gasket, differential, assembly to rear axle housing, power dividers, axle shaft flanges Directions:Surfaces should be clean & dry. Apply a continuous, uniform 1/16” to 1/4” bead of silicone, surrounding all bolt holes. 1/8” is suitable for most applications. Bead size may be varied by finger pressure, how quickly applicator is moved and angle. For heavier beads, nozzle may be cut to size. Activate PowerBead™ by twisting nozzle one full turn counterclockwise, raising trigger. Press trigger to dispense. Assemble parts immediately while silicone is still wet. Silicone will fully cure in 24 hours. After use, store applicator by twisting nozzle clockwise, wiping away excess silicone and replacing plastic cap with a “click”.NOTE: Not recommended for use on head gaskets or parts in contact with gasoline. Normalized SKU: 85084UPC Code: 686226850843

Loctite-Permatex 42274 ShopSCRUBS® In-A-Bucket® - 72-PieceSCRUBS® In-A-Bucket® Cleaning Towels combine an advanced, patented cleaning formula with an industrial strength, dual-textured towel to thoroughly clean hands and surfaces ANYWHERE, ANYPLACE, ANYTIME! The clean, citrus-scented formula loosens and dissolves industrial soils while leaving hands free from dryness and irritation. The Rough Touch® blue towel locks in soils to prevent them from transferring back onto hands and surfaces. Hands are left feeling clean with no sticky residue and no rinsing required.Applications:Suggested Applications: Removal of dirt, soil, grease, grime, paints, urethanes, inks, dyes, lubricants, oils, adhesives, caulks, tar, and asphaltDirections: Open lid. Pull towel out quickly to separate from next towel. Use each side of the towel until cleaned to satisfaction or until towel becomes too dirty to absorb more. If necessary, repeat process with more towels until surface is clean. Dispose of with normal trash. Do not flush used towels. Normalized SKU: 42274UPC Code: 764769422748

Loctite-Permatex 82112 Adhesives & SealantsSelf-Fusing Silicone Tape 1" x 10"A self-fusing silicone repair tape that has been used by the Military for years! An all-purpose repair tape that is made out of specially formulated silicone rubber. Contains no adhesives; yet chemically bonds to itself upon contact. Simply stretch and wrap for an airtight, waterproof seal in seconds. Replaces duct tape and electrical tape. Applications:Automobile: Use to seal, insulate and stop vibration on just about anything you are able to get a couple of wraps around. Seal electrical connections, make emergency fuel or water hose repairs, insulate wiring and hoses, repair leaking pipes and hoses, repair damaged wires, and wrap hand tools and grips. Use connector wires and cables, all kinds of hoses such as garden hoses, vacuum hoses, appliance cords, and radiator hoses. Normalized SKU: 82112UPC Code: 686226821126