Victron Energy BAT512120740 Batteries The Lithium SuperPack NG 12.8V 200Ah battery is a true drop-in replacement for standard lead-acid batteries, offering ample capacity for extended off-grid use while powering complete electrical systems, including high-demand appliances, with an easy fit for large trucks, SUVs, and RVs thanks to its compatible form factor and terminal layout. Bluetooth monitoring and control via Bluetooth Smart allows wireless configuration, monitoring, and firmware updates using the VictronConnect App, with Instant Readout showing state of charge, battery temperature, warnings, and alarms directly in the device list without connecting Built-in BMS and battery monitor provide integrated cell balancing, protection, and monitoring to ensure optimal performance and safety over the battery service life External Feedback Signal provides a battery voltage signal limited to 250 mA and can act as an External Disconnection Signal for redundant system protection or as an External Charging Signal based on the low state of charge pre-alarm threshold to trigger a charger start Self-heating function keeps the battery above the minimum safe charging temperature for reliable cold-weather operation with charger mode using external charger power below 0 °C and auto mode using battery power until the low state of charge threshold is reached LED status indication uses two integrated LEDs to show Bluetooth connectivity, warnings, alarms, and firmware update status On and off push button allows safe shutdown of charging and discharging for operation or extended storage High efficiency operation delivers up to 93% efficiency Parallel connection supports an unlimited number of batteries to increase total energy capacity, as long as total system current stays within the safe interrupt rating of a single battery Configurable discharge floor lets users set a minimum state of charge to prevent excessive discharge while maintaining reserve capacity, with low state of charge alarms and discharge lockout until recovery Nominal voltage: 12.8 volts Nominal capacity at 25°C: 200 Ah Nominal energy at 25°C: 2560 Wh Capacity loss per 100 cycles at 25°C and 100% depth of discharge: less than 5% Round-trip efficiency: 93% Cycle life at 25°C: 80% depth of discharge: 2500 cycles 70% depth of discharge: 3000 cycles 50% depth of discharge: 5000 cycles Discharge: Maximum continuous discharge current: 400 amp End of discharge voltage: 11.2 volts Internal resistance: 1 mΩ Charge: Recommended charge voltage: 14 volts Float voltage: 13.5 volts Charge voltage range: 13.5 to 14.2 volts Maximum continuous charge current: 200 amp Features: Hardware protection: system max current short circuit above 800 amps Software protections: overvoltage, undervoltage, overtemperature, undertemperature, overcurrent Wired communication: external feedback signal Bluetooth: yes, VictronConnect App User interface: push button on and off, blue LED, error LED Self-heating max power: 130 watts Operating conditions: Parallel configuration: yes, unlimited energy expansion within system current limits Series configuration: no Operating temperature: charge and discharge from -30°C to 60°C Humidity operating range: less than 90% RH, non-condensing Storage temperature: recommended 10°C to 35°C, extended -40°C to 65°C Max storage time at 25°C: 1 year with at least 50% state of charge Protection class: IP65 Mounting: Power connection: M8 female threaded insert Mounting options: upright or on its side, maintain flat horizontal support Dimensions: 466 x 198 x 173 mm (18.35 × 7.80 × 6.81 inches) Weight: 20.5 kg (45.2 pounds) Standards: Cells: UL1973 Safety approvals: UL9540A, IEC62619 Normalized SKU: BAT512120740

Victron Energy BAT512110740 Batteries The Lithium SuperPack NG 12.8 volt 100Ah battery is a true drop-in replacement for standard lead acid batteries, offering ample capacity for extended off-grid use while powering complete electrical systems, including high-demand appliances, with an easy fit for large trucks, SUVs, and RVs thanks to its compatible form factor and terminal layout. Bluetooth monitoring and control via Bluetooth Smart allows wireless configuration, monitoring, and firmware updates using the VictronConnect App, with Instant Readout showing state of charge, battery temperature, warnings, and alarms directly in the device list without connecting Built-in BMS and battery monitor provide integrated cell balancing, protection, and monitoring to ensure optimal performance and safety over the battery service life External Feedback Signal provides a battery voltage signal limited to 250 mA and can act as an External Disconnection Signal for redundant system protection or as an External Charging Signal based on the low state of charge pre-alarm threshold to trigger a charger start Self-heating function keeps the battery above the minimum safe charging temperature for reliable cold-weather operation with charger mode using external charger power below 0 °C and auto mode using battery power until the low state of charge threshold is reached LED status indication uses two integrated LEDs to show Bluetooth connectivity, warnings, alarms, and firmware update status On and off push button allows safe shutdown of charging and discharging for operation or extended storage High efficiency operation delivers up to 93% efficiency Parallel connection supports an unlimited number of batteries to increase total energy capacity, as long as total system current stays within the safe interrupt rating of a single battery Configurable discharge floor lets users set a minimum state of charge to prevent excessive discharge while maintaining reserve capacity, with low state of charge alarms and discharge lockout until recovery Nominal voltage: 12.8 volts Nominal capacity at 25°C: 100 Ah Nominal energy at 25°C: 1280 Wh Capacity loss per 100 cycles at 25°C and 100% depth of discharge: less than 5% Round-trip efficiency: 93% Cycle life at 25°C: 80% depth of discharge: 2500 cycles 70% depth of discharge: 3000 cycles 50% depth of discharge: 5000 cycles Discharge: Maximum continuous discharge current: 200 amps End of discharge voltage: 11.2 volts Internal resistance: 2 mΩ Charge: Recommended charge voltage: 14 volts Float voltage: 13.5 volts Charge voltage range: 13.5 to 14.2 volts Maximum continuous charge current: 100 amps Features: Hardware protection: system max current short circuit above 800 amps Software protections: overvoltage, undervoltage, overtemperature, undertemperature, overcurrent Wired communication: external feedback signal Bluetooth: yes, VictronConnect App User interface: push button on and off, blue LED, error LED Self-heating max power: 65 watts Operating conditions: Parallel configuration: yes, unlimited energy expansion within system current limits Series configuration: no Operating temperature: charge and discharge from -30°C to 60°C Humidity operating range: less than 90% RH, non-condensing Storage temperature: recommended 10°C to 35°C, extended -40°C to 65°C Max storage time at 25°C: 1 year with at least 50% state of charge Protection class: IP65 Mounting: Power connection: M8 female threaded insert Mounting options: upright or on its side, maintain flat horizontal support Dimensions: 273 x 173 x 173 mm (10.7 x 6.8 x 6.8 inches) Weight: 10.7 kg (23.6 pounds) Standards: Cells: UL1973 Safety approvals: UL9540A, IEC62619 Normalized SKU: BAT512110740

Victron Energy BAT512110610 BatteriesLithium Battery 12VDC - 100AH - Smart LifePO4Features: With integrated cell balancing Can be parallel and series connected  Bluetooth app available to monitor cell voltage and temperature Requires one of these BMS-es: VE.Bus BMS – recommended for systems with our inverter/chargers. smallBMS – recommended for use in small systems.  Battery Management System BMS 12/200 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Smart BMS 12/200 - recommended for use in Automotive and Marine systems having DC-loads and Alternators.  Smart BMS CL 12/100 – recommended for use in Automotive and Marine systems having DC-loads and Alternators. Lynx Smart BMS - recommended for use in large systems. Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: BAT512110610UPC Code: 8719076043041

Victron Energy BAT412123081 Batteries Engineered with cutting-edge battery electrochemistry, the Victron Energy 12v/230ah AGM Super Cycle Battery is designed for heavy-duty use. With a 20-hour rate of 230Ah and 700 CCA, this battery can handle frequent deep discharges without compromising performance. Its M8 terminals and high reserve capacity make it ideal for applications that require occasional or frequent 100% discharge. Plus, with a DoD rating of up to 1000 cycles, this battery offers long-lasting reliability. Normalized SKU: BAT412123081

Mastervolt 66011250 Batteries MLI Ultra 12/1250-1.25 kWh Battery Replaces Mastervolt 66021250 Normalized SKU: 66011250

Download LiteratureVictron Energy BAT524110620 BatteriesLithium Battery 24VDC 100Ah NG Smart LifePO4The NG (Next Generation) series builds on the achievements of the Lithium Smart Series, featuring substantial improvements. Designed for individuals in need of sophisticated and dependable energy storage solutions, the Lithium NG series represents a crucial development in our product range, prepared to address the challenges of the future.Victron Energy Lithium NG batteries are Lithium Iron Phosphate (LiFePO4 or LFP) batteries available with nominal voltages of 12.8V, 25.6V, and 51.2V in various capacities. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12V, 24V, or 48V. The maximum number of batteries in one system is 50, which results in a maximum energy storage of 192 kWh in a 12V system and up to 384 kWh in a 24V and 48V system.Integrated shuntThe battery data (battery voltage, current, and temperature) are transmitted to the BMS and evaluated there, i.e. to calculate the state of charge, which can then be read out via VictronConnect or a GX communication center, or to create and issue specific warnings and alarms.Automatic setup, monitoring, and control via VictronConnect App or a GX device and the VRM PortalAll battery parameters are managed by the BMS automatically. The BMS automatically detects the system voltage and the number of batteries in parallel, series, and series/parallel connections. The BMS (from now on Lynx Smart BMS NG 500 A/1000 A, further models to follow) is mandatory and must be purchased separately.Monitoring and control take place via VictronConnect (every BMS model has Bluetooth), a GX communication center, or the VRM Portal. You can view battery parameters such as cell status, cell voltages, battery current, and temperatures in real time. The battery firmware is automatically updated by the BMS.Easy bracket mountingMounting brackets make the installation easier and ensure that the battery is optimally secured against slipping and tipping over.Increased ingress protection (IP-rating)The Lithium NG batteries are effectively sealed against dust and can withstand low-pressure water jets, making them suitable for environments where exposure to dust and water is a concern.Low self-discharge rateThe self-discharge rate has been significantly improved and is now a maximum of 2 % of the battery capacity per month. A low self-discharge rate contributes to the overall performance, longevity, and reliability of the NG batteries.Features: Multiple improvements including added read-out of cell voltages and temperatures Maximum single bank size increased to 385kWh Modules available in 12, 24 and 48V Protection class IP65 Bracket mounting and strap mounting Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: BAT524110620UPC Code: 8719076058939Victron Energy BAT524110620 Literature Download Quick Reference Guide Owners Manual

Download LiteratureXantrex 886-0050-24 Batteries24V 50Ah Lithium-Ion BatteryHigh cycle Lithium-Ion (LiFePO4) battery designed to fit into existing lead acid Group 31 battery scenarios such as powering trolling motors for fishing boats.More Power in Less SpaceThe Xantrex Lithium-Ion Iron Phosphate (LiFePO4) battery used UL1642-certified cells. Equipped with redundant safety features, it is the safest in the market today. Specifically designed to withstand the harsh operating environments of mobile and marine applications, the battery lasts up to 4,000 cycles compared to a traditional lead acid or AGM battery, which typically lasts 400-500 cycles. It offers exceptional power density and is also available with a heating blanket option if the installation is outside the main cabin.Sleep Mode: Xantrex Lithium-Ion Iron Phosphate batteries self-discharge at 12.5% State of Charge (SOC) per month during regular use. After 10 consecutive days of inactivity, the battery switches to a low-power mode, reducing the self-discharge rate to 3% SOC per month. Any charge or discharge activity will reactivate the battery, resetting the 10-day counter. This extends the battery life during periods of non-use.Sleep ModeReduces self-discharge to 3% from 12.5% State of Charge per month after 10 days of inactivity, enhancing battery life.High Temperature RatingCapable of being charged up to 55°C/131°F allows extreme environment recharge without damage to the battery.Bluetooth ConnectivityConnect to the Xantrex App to see the battery status from your smart device.Lithium Iron Phosphate vs. Lead AcidWith the advances in technology, you can get more charge cycles and more energy per cycle from a LiFePO4 battery than a traditional AGM or Gel Cell lead acid battery.Features: View SOX and faults directly Extreme high and low temperatures Remote on/off and fault Self-protection BMS included Applications: Recreational Vehicles Heavy Duty Trucks Work Trucks Marine Specialty Vehicles Certifications: UN/DOT 38.3 Lithium IonThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Normalized SKU: 886005024Xantrex 886-0050-24 Literature Download Quick Reference Guide Owners Manual

Download LiteratureVictron Energy BAT524130620 BatteriesLithium Battery 24VDC 300Ah NG Smart LifePO4The NG (Next Generation) series builds on the achievements of the Lithium Smart Series, featuring substantial improvements. Designed for individuals in need of sophisticated and dependable energy storage solutions, the Lithium NG series represents a crucial development in our product range, prepared to address the challenges of the future.Victron Energy Lithium NG batteries are Lithium Iron Phosphate (LiFePO4 or LFP) batteries available with nominal voltages of 12.8V, 25.6V, and 51.2V in various capacities. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12V, 24V, or 48V. The maximum number of batteries in one system is 50, which results in a maximum energy storage of 192 kWh in a 12V system and up to 384 kWh in a 24V and 48V system.Integrated shuntThe battery data (battery voltage, current, and temperature) are transmitted to the BMS and evaluated there, i.e. to calculate the state of charge, which can then be read out via VictronConnect or a GX communication center, or to create and issue specific warnings and alarms.Automatic setup, monitoring, and control via VictronConnect App or a GX device and the VRM PortalAll battery parameters are managed by the BMS automatically. The BMS automatically detects the system voltage and the number of batteries in parallel, series, and series/parallel connections. The BMS (from now on Lynx Smart BMS NG 500 A/1000 A, further models to follow) is mandatory and must be purchased separately.Monitoring and control take place via VictronConnect (every BMS model has Bluetooth), a GX communication center, or the VRM Portal. You can view battery parameters such as cell status, cell voltages, battery current, and temperatures in real time. The battery firmware is automatically updated by the BMS.Easy bracket mountingMounting brackets make the installation easier and ensure that the battery is optimally secured against slipping and tipping over.Increased ingress protection (IP-rating)The Lithium NG batteries are effectively sealed against dust and can withstand low-pressure water jets, making them suitable for environments where exposure to dust and water is a concern.Low self-discharge rateThe self-discharge rate has been significantly improved and is now a maximum of 2 % of the battery capacity per month. A low self-discharge rate contributes to the overall performance, longevity, and reliability of the NG batteries.Features: Multiple improvements including added read-out of cell voltages and temperatures Maximum single bank size increased to 385kWh Modules available in 12, 24 and 48V Protection class IP65 Bracket mounting and strap mounting Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: BAT524130620UPC Code: 8719076064749Victron Energy BAT524130620 Literature Download Quick Reference Guide Owners Manual

Download LiteratureXantrex 886-0050-36 Batteries36V 50Ah Lithium-Ion BatteryHigh cycle Lithium-Ion (LiFePO4) battery designed to fit into existing lead acid Group 31 battery scenarios such as powering trolling motors for fishing boats.More Power in Less SpaceThe Xantrex Lithium-Ion Iron Phosphate (LiFePO4) battery used UL1642-certified cells. Equipped with redundant safety features, it is the safest in the market today. Specifically designed to withstand the harsh operating environments of mobile and marine applications, the battery lasts up to 4,000 cycles compared to a traditional lead acid or AGM battery, which typically lasts 400-500 cycles. It offers exceptional power density and is also available with a heating blanket option if the installation is outside the main cabin.Sleep Mode: Xantrex Lithium-Ion Iron Phosphate batteries self-discharge at 12.5% State of Charge (SOC) per month during regular use. After 10 consecutive days of inactivity, the battery switches to a low-power mode, reducing the self-discharge rate to 3% SOC per month. Any charge or discharge activity will reactivate the battery, resetting the 10-day counter. This extends the battery life during periods of non-use.Sleep ModeReduces self-discharge to 3% from 12.5% State of Charge per month after 10 days of inactivity, enhancing battery life.High Temperature RatingCapable of being charged up to 55°C/131°F allows extreme environment recharge without damage to the battery.Bluetooth ConnectivityConnect to the Xantrex App to see the battery status from your smart device.Lithium Iron Phosphate vs. Lead AcidWith the advances in technology, you can get more charge cycles and more energy per cycle from a LiFePO4 battery than a traditional AGM or Gel Cell lead acid battery.Features: View SOX and faults directly Extreme high and low temperatures Remote on/off and fault Self-protection BMS included Applications: Recreational Vehicles Heavy Duty Trucks Work Trucks Marine Specialty Vehicles Certifications: UN/DOT 38.3 Lithium IonThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Normalized SKU: 886005036UPC Code: 715535926649Xantrex 886-0050-36 Literature Download Quick Reference Guide Owners Manual

Download LiteratureVictron Energy BAT512118610 BatteriesLithium Battery 12VDC - 180AH - Smart LifePO4 - Drop Ship Only for $150Victron Energy Lithium Battery Smart batteries are Lithium Iron Phosphate (LiFePO4). They are available in capacities of 12.8 V or 25.6 V. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12 V, 24 V, or 48 V. The maximum number of batteries in one system is 20, which results in a maximum energy storage of 84 kWh in a 12 V system and up to 102 kWh in a 24 V1) and 48 V1) system. A single LFP cell has a nominal voltage of 3.2 V. A 12.8 V battery consists of 4 cells connected in series and a 25.6 V battery consists of 8 cells connected in series.Why lithium-iron-phosphate?Rugged A lead-acid battery will fail prematurely due to sulfation:  If it operates in deficit mode during long periods (i.e., if the battery is rarely, or never fully charged).  If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime).  A LFP battery:  Does not need to be fully charged. Service life even slightly improves in case of a partial charge instead of a full charge. This is a major advantage of LFP compared to lead acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance, and high efficiency (see below).  LFP is therefore the chemistry of choice for demanding applications.Efficient  In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance.  The round-trip energy efficiency (discharge from 100 % to 0 % and back to 100 % charged) of the average lead-acid battery is 80 %.  The round-trip energy efficiency of a LFP battery is 92 %.  The charge process of lead-acid batteries becomes particularly inefficient when the 80 % state of charge has been reached, resulting in efficiencies of 50 % or even less in solar systems where several days of reserve energy is required (battery operating in 70 % to 100 % charged state).  In contrast, an LFP battery will still achieve 90 % efficiency under shallow discharge conditions. Size & Weight  Saves up to 70 % in space  Saves up to 70 % in weight  Expensive? LFP batteries are expensive when compared to lead-acid. However, in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability, and excellent efficiency. Bluetooth  With Bluetooth cell voltages, temperature and alarm status can be monitored.  Instant readout: The VictronConnect App can display the most important data on the Device list page without the need to connect to the product.  Very useful to localize a (potential) problem, such as cell imbalance.  Six tailored BMS solutions There are 6 different BMS models tailored for various applications available for use with the Lithium Battery Smart. The system design and BMS selection guide in the battery manual provide an overview and explain the differences between them and their typical use.1) To reduce the required balancing time, Victron recommends using as few different batteries in series as possible for the application. 24 V systems are best built using 24 V batteries. 48 V systems are best built using two 24 V batteries in series. While the alternative, four 12 V batteries in series, will work, it will require more periodic balancing time.Victron LFP batteries have integrated cell balancing and cell monitoring. The cell balancing/monitoring cables can be daisy-chained and must be connected to a Battery Management System (BMS). The BMS will:  Generate a pre-alarm whenever the voltage of a battery cell decreases to less than 3.1 V (adjustable 2.85 V – 3.15 V).  Disconnect or shut down the load whenever the voltage of a battery cell decreases to less than 2.8 V (adjustable 2.6 V – 2.8 V).  Stop the charging process whenever the voltage of a battery cell increases to more than 3.75 V or when the temperature becomes too high or too low.  Specifications:Battery Specs: Nominal Voltage: 12,8 V Nominal Capacity @ 25 °C*: 180 Ah Nominal capacity @ 0 °C*: 150 Ah Nominal capacity @ -20 °C*: 90 Ah Nominal energy @ 25 °C*: 2304 Wh *Discharge current ≤1C Cycle Life (capacity ≥ 80 % of nominal): 80 % DoD: 2500 cycles  70 % DoD: 3000 cycles  50 % DoD: 5000 cycles Discharge: Maximum Continuous Discharge Current: 360 A Recommended Continuous Discharge Current: ≤180 A End of Discharge Voltage: 11.2 V Internal Resistance: 0.9 mΩ Operating Conditions: Operating Temperature: Discharge: -20 °C to +50 °C; Charge: +5 °C to +50 °C  Storage Temperature: -45 °C to +70 °C  Humidity (non-condensing): Max. 95 %  Protection Class: IP 22 Charge: Charge Voltage: Between 14 V/28 V and 14,4 V/28,8 V (14,2 V/28,4 V recommended) Float Voltage: 13,5 V/27 V Maximum Current Charge: 360 A Recommended Charge Current: ≤90 A Mounting:Can Be Placed on Their Sides: YesOther:  Max Storage Time @ 25°C): 1 year BMS Connection: Male + female cable with M8 circular connector, length 50 cm Power connection (threaded inserts): M8 Dimensions (H x W x D): 237 x 321 x 152 mm Weight: 18 kg Standards: Safety: EN 60335-1:2012/AC:2014,  EN-IEC 62368-1: 2020, IEC 61427-1:2013 EMC: EN-IEC 61000-6-3:2007/A1:2011/AC:2012 - EN 55014-1:2017/A11:2020 Automotive: ECE R10-6 Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: BAT512118610UPC Code: 8719076060260Victron Energy BAT512118610 Literature Download Quick Reference Guide Owners Manual Product Brochure

Download Literature Watch VideoVictron Energy BAT524120620 BatteriesLithium NG Smart Battery 24VDC - 200AH - Smart LifePO4 - 24VVictron Energy Lithium NG batteries are Lithium Iron Phosphate (LiFePO4 or LFP) batteries available in various capacities with nominal voltages of 12.8V, 25.6V, and 51.2V. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12V, 24V, or 48V. The maximum number of batteries in one system is 50, which results in a maximum energy storage of 192kWh in a 12V system and up to 384kWh in a 24V and 48V system.Integrated ShuntThe battery data (battery voltage, current, and temperature) are transmitted to the BMS and evaluated there, i.e., to calculate the state of charge, which can then be read out via VictronConnect or a GX communication center, or to create and issue specific warnings and alarms.Automatic Setup, Monitoring, and Control via the VictronConnect App or a GX Device and the VRM PortalThe BMS automatically manages all battery parameters. The BMS automatically detects the system voltage and the number of batteries in parallel, series, and series/parallel connections. The BMS (from now on, Lynx Smart BMS NG 500 A/1000 A; further models to follow) is mandatory and must be purchased separately. Monitoring and control take place via VictronConnect (every BMS model has Bluetooth), a GX communication center, or the VRM Portal. Users can view battery parameters such as cell status, cell voltages, battery current, and temperatures in real-time. The battery firmware is automatically updated by the BMS.Easy Bracket MountingMounting brackets make the installation easier and ensure that the battery is optimally secured against slipping and tipping over.Increased Ingress Protection (IP-rating)The lithium-ion NG batteries are effectively sealed against dust and can withstand low-pressure water jets, making them suitable for environments where exposure to dust and water is a concern.Low Self-Discharge RateThe self-discharge rate has been significantly improved and is now a maximum of 2% of the battery capacity per month. A low self-discharge rate contributes to the overall performance, longevity, and reliability of the NG batteries.Victon’s lithium-ion NG batteries have integrated cell balancing and cell monitoring. The cell balancing/monitoring cables can be daisy-chained and must be connected to a Battery Management System (BMS). Battery Management System (BMS) BMS will: Generate a pre-alarm whenever the voltage of a battery cell decreases to less than 3.0 V Disconnect or shut down the load whenever the voltage of a battery cell decreases to less than 2.8 V Stop the charging process whenever the voltage of a battery cell increases to more than 3.6 V or when the temperature becomes too high or too low Other Features:Victron Smart products can connect through Bluetooth, USB/Wifi/LAN, or remotely via the internetSpecifications:Voltage & Capacity:  Nominal Voltage: 25.6 V Nominal Capacity @ 25 °C: 200 Ah Nominal Energy @ 25 °C: 5120 Wh Discharge Current ≤1C: N/A Cycle Life (capacity ≥ 80 % of nominal): 80 % DoD: 2,500 cycles 70 % DoD: 3,000 cycles 50 % DoD: 5,000 cycles Discharge: Max Continuous Discharge Current: 200 A Max Pulse Discharge Current (10s): 400 V End of Discharge Voltage: 22.4 Internal Resistance: 2 mΩ Charge: Charge Voltage: Between 14 V / 28 V / 56 V and 14,4 V / 28,8 V / 56,8 V Float Voltage: 13,5 V / 27 V 54 V Max Continuous Charge Current: 100 A Max Pulse Charge Current (10s): 200 A General:  BMS-es: Lynx Smart BMS NG 500 A / 1000 A (M10 busbars), must be purchased separately Cell Measurements: Cell voltages and temperatures, battery current Battery BMS Interface: Male + female cable with M8 circular connector with high-speed digital communication, length 50 cm M8 extension cables are available separately for purchase in various lengths between 1 and 5 meters Alarm Feature: Pre-alarm contact on BMS Bluetooth: In the BMS Max Batteries Per BMS: 50 (384 kWh per BMS 3)) Battery Firmware Updates: Battery firmware automatically updated by BMS Repairable: Yes (cover can be removed with screws) Operating Conditions: Operating Temperature: Discharge: -20 °C to +50 °C | Charge: +5 °C to +50 °C Storage Temperature: -45 °C to +70 °C Humidity (non-condensing): Max. 95 % Protection Class: IP65 Mounting: Mounting Options: Strap or mounting brackets Can be Placed on Their Sides: Yes Other: Self-Discharge Rate: ≤ 3 % per month @ 25 °C Power Connection: M8 (threaded inserts and bolts) Dimensions (H x W x D) mm: 235 x 648 x 162 Weight (est.): 37 kg Standards: Safety: Cells: UL1973 UL9540A IEC62619 EMC: Battery: IEC  62619 (pending) Automotive: EN 61000-6-3, EN 61000-6-2 Performance: IEC 62620 (pending) Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: BAT524120620UPC Code: 8719076057529Victron Energy BAT524120620 Literature Download Quick Reference Guide Owners ManualVictron Energy BAT524120620 Video