Watch VideoLenco Marine 15501-101 Trim TabsA Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically!The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again!The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency.The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad.The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver.Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications.For Aftermarket Systems:The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System:For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains1 30254-001D Auto Glide Key Pad Control1 30256-001 Auto Glide Control Box f/ Dual Actuator1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5'1 30262-001D CAN bus #2 GPS/NMEA 2000 Network Adapter Cable - 2.5'1 30266-001 NMEA 2000 GPS Antenna Only3 30267-001D Tee Connector Only2 30268-001D Terminating Resistor - Female1 30268-002D Terminating Resistor - Male1 30281-001D Power Cable - NMEA 2000 Network 2.5'Available for these CANbus-based engines:NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Actuator Type = NONE Boat Length - Max (Feet) = NONE Construction = NONENormalized SKU: 15501101UPC Code: 874847006729Lenco Marine 15501-101 Video

  Watch VideoLenco Marine 15500-101 Trim TabsAuto Glide Boat Leveling SystemA Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically!The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again!The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency.The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad.The main components are the Auto Glide Key Pad, the Auto Glide Control Box, the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver.Boat must have Lenco Single Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications.For Aftermarket Systems:The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System:For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains1 30254-001D Auto Glide Key Pad Control1 30255-001 Auto Glide Control Box f/ Single Actuator1 30248-001 Auto Glide Control Box Harness f/ Single Actuator1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5'1 30262-001D CAN bus #2 GPS/NMEA 2000 Network Adapter Cable - 2.5'1 30266-001 NMEA 2000 GPS Antenna Only3 30267-001D Tee Connector Only2 30268-001D Terminating Resistor - Female1 30268-002D Terminating Resistor - Male1 30281-001D Power Cable - NMEA 2000 Network 2.5'Available for these CANbus-based engines:NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda SuzukiE Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Actuator Type = NONE Boat Length - Max (Feet) = NONE Construction = NONENormalized SKU: 15500101UPC Code: 874847006712Lenco Marine 15500-101 Video

Lenco Marine 15153-001 Trim TabsLenco 4-1/4" Stroke XD Actuator 5/16" x 3/8" 12v #15153-001Normalized SKU: 15153001UPC Code: 874847007863

  Download Literature  Watch VideoLenco Marine 15062-001 Trim Tabs101 XD Actuator- 24 Volt- 2-1/4  Stroke with Mounting HardwareThe 101 XD Actuator is used mostly with HD, XD, High Performance and Super Strong tabs. 2.25 stroke. Overall length (tip to tip) is 113/8 inches.   Instant response electric actuators are made of high impact glass fiber filled, ultraviolet-resistant nylon material with 316 super buff stainless steel tubing.Specifications: Newly implemented Anti Extrusion Ring (AXR) seal stabilization system. Stronger top cap and mounting clevis design Improved pressure-tight torx screws Integrated wiper seal at actuator base Molded-in brass thrust bearing design Thicker and stronger motor housing wall Improved O-Ring design for more consistent seal Over-molded cable providing a stronger tighter seal Upper mounting bracket with gland seal Features: Lenco's ballscrew design is more reliable and twice as powerful compared to typical hydraulics Lenco's tough, high-torque actuator motor easily pushes 500 pounds. Lenco Actuator connections use waterproof "Plug & Play" Deutsch connectors eliminating the possibility of water intrusion. 24 Volt 5/16" mounting hardware 6 foot cable WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 15062001UPC Code: 874847003278Lenco Marine 15062-001 Literature Download  Quick Reference GuideLenco Marine 15062-001 Video

Lenco Marine 15152-001 Trim TabsLenco 2-1/4" Stroke XDS Actuator 5/16" x 3/8" 12v #15152-001Normalized SKU: 15152001UPC Code: 874847007856

Lenco Marine 15505-101 Trim TabsLenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically!The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again!The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency.The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad.The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver.Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications.For Aftermarket Systems:The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System:For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains1 30254-001D Auto Glide Key Pad Control1 30256-001 Auto Glide Control Box f/ Dual Actuator1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5'Available for these CANbus-based engines:NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 15505101UPC Code: 874847007283

Lenco Marine 15504-101 Trim TabsAuto Glide Boat Leveling System for Single Actuator Tab Systems w/Existing NMEA 2000A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically!The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again!The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency.The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad.The main components are the Auto Glide Key Pad, the Auto Glide Control Box, the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver.Boat must have Lenco Single Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications.For Aftermarket Systems:The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System:For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains1 30254-001D Auto Glide Key Pad Control1 30255-001 Auto Glide Control Box f/ Single Actuator1 30248-001 Auto Glide Control Box Harness f/ Single Actuator1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5'Available for these CANbus-based engines:NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda SuzukiE Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 15504101UPC Code: 874847007276

Lenco Marine 15063-002 Trim Tabs 2 1/4 in. XD Replacement Actuator 12V 6 ft. wire 5/16 in. top cap hole 5/16 in. end hole Normalized SKU: 15063002UPC Code: 874847006262

  Download Literature  Watch VideoLenco Marine 15066-001 Trim Tabs102 Series Standard Actuator - 24V - 4-1/4" Stroke w/HardwareThe 102 Actuator is used with Trolling Tab systems sold prior to 2000 and OEM applications. 4.25 stroke. Overall length (tip to tip) is 14 inches. Instant response electric actuators are made of high impact glass fiber filled, ultraviolet-resistant nylon material with 316 super buff stainless steel tubing.Specifications: Newly implemented Anti Extrusion Ring (AXR) seal stabilization system. Stronger top cap and mounting clevis design Improved pressure-tight torx screws Integrated wiper seal at actuator base Molded-in brass thrust bearing design Thicker and stronger motor housing wall Improved O-Ring design for more consistent seal Over-molded cable providing a stronger tighter seal Upper mounting bracket with gland seal Features: Lenco's ballscrew design is more reliable and twice as powerful compared to typical hydraulics Lenco's tough, high-torque actuator motor easily pushes 500 pounds. Lenco Actuator connections use waterproof "Plug & Play" Deutsch connectors eliminating the possibility of water intrusion. 24 Volt 5/16" mounting hardware 6 foot cable WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 15066001UPC Code: 874847003315Lenco Marine 15066-001 Literature Download  Quick Reference GuideLenco Marine 15066-001 Video