Victron Energy SCC110050210 Battery ChargersSmartSolar MPPT Charge Controller - 100V - 50AMPFeatures: Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.  VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices  Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Internal temperature sensor Compensates absorption and float charge voltage for temperature.  Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers Normalized SKU: SCC110050210UPC Code: SCC110050210

ProMariner 44029 Battery Chargers ProSportHD 20 Plus Global Gen 4 - 20 Amp - 3-Bank Battery Charger ProSportHD Generation 4 boasts a tri-surface heatsink design. This heavy-duty lightweight design delivers significantly faster charging through optimal cooling while delivering true rated amp output during charge mode.  ProSportHD's enhanced microprocessor and software provides digital features including fuel gauge style Charge Completion Monitor, Charge Mode, individual Fault indicators, and three digitally selectable performance charge profiles for Flooded (lead-acid), AGM, and GEL batteries. HP AGM profile on ProSportHD 20 Dual only.  Fully automatic 5-stage charging enhances battery performance while extending battery life. System Check OK and Battery Status indicators provide real-time installation and battery fault status.  Designed for use in harsh environments with our industrial-grade jacketed DC and AC power cables which include molded strain reliefs and wire splitters.  Features: ProMar Digital Technology Microprocessor and software controlled charging technology for fast, precise charging Distributed-On-Demand™ Technology 100% of all available charging amps are utilized by distributing unused charging amps to any one or combination of all batteries as needed Heavy Duty Tri-Surface Extruded Heat Sink Design Upper, lower, and rear-facing heat sink design for optimal cooling while delivering true rated constant current charging amps during its two charge mode Expanded LED Display with Completion Status Gauge LED fuel gauge style completion status. Four-color multi-stage mode LED status bar. Multi-stage Charge Mode, System Check OK, individual Battery Status and Battery Type indication Lightweight Design Up to 40% lighter compared to an epoxy filled charger Auto-Maintain Energy Saver Mode Monitor and auto maintain batteries only when needed to maintain a full state of charge. This significantly reduces AC power consumption Fully Automatic 5-Stage Digital Performance Charging 5 Stages: Analyzes, charges, conditions, auto maintains, and reconditions batteries once a month during storage periods. Fully charges and extends battery life Built-in Quality and Safety Dual inline waterproof fuses, reverse polarity, over-temperature, over-current, over-voltage, and ignition protection. Certified to Marine UL 1236. CEC and DOE listed. FCC Class B Easy Installation and Operation Pre-wired with 6’ AC and DC cables Battery Type: Group 24–31 Flooded, AGM, HP AGM, and GEL batteries 3 Year Warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Portable = NONE Charging Banks = 3 Bank Charger Output Voltage = NONE Charger Output - Amps = 20 Amp Charger Input - Voltage = NONE Normalized SKU: 44029UPC Code: 031669440296

ProMariner 44008 Battery ChargersProSportHD 8 Gen 4 - 8 Amp - 2 Bank Battery ChargerProSportHD Generation 4 boasts a tri-surface heatsink design. This heavy-duty lightweight design delivers significantly faster charging through optimal cooling, while delivering true rated amp output during charge mode. ProSportHD's enhanced microprocessor and software provides digital features including: fuel gauge style Charge Completion Monitor, Charge Mode, individual Fault indicators and three digitally selectable performance charge profiles for Flooded (lead acid), AGM and GEL batteries. HP AGM profile on ProSportHD 20 Dual only. Fully automatic 5-stage charging enhances battery performance while extending battery life. System Check OK and Battery Status indicators provide real time installation and battery fault status. Designed for use in harsh environments with our industrial grade jacketed DC and AC power cables which include molded strain reliefs and wire splitters. Features: ProMar Digital Technology Microprocessor and software controlled charging technology for fast, precise charging Distributed-On-Demand™ Technology 100% of all available charging amps are utilized by distributing unused charging amps to any one or combination of all batteries as needed Heavy Duty Tri-Surface Extruded Heat Sink Design Upper, lower and rear facing heat sink design for optimal cooling while delivering true rated constant current charging amps during its two charge mode Expanded LED Display with Completion Status Gauge LED fuel gauge style completion status. Four color multi-stage mode LED status bar. Multi-stage Charge Mode, System Check OK, individual Battery Status and Battery Type indication Lightweight Design Up to 40% lighter compared to an epoxy filled charger Auto-Maintain Energy Saver Mode Monitor and auto maintain batteries only when needed to maintain full state of charge. This significantly reduces AC power consumption Fully Automatic 5-Stage Digital Performance Charging 5 Stages: Analyzes, charges, conditions, auto maintains and reconditions batteries once a month during storage periods. Fully charges and extends battery life Built-in Quality and Safety Dual inline waterproof fuses, reverse polarity, over-temperature, over-current, over-voltage and ignition protection. Certified to Marine UL 1236. CEC and DOE listed. FCC Class B Easy Installation and Operation Pre-wired with 6’ AC and DC cables Battery Type: Group 24–31 Flooded, AGM, HP AGM and GEL batteries 3 Year Warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 44008UPC Code: 031669440081

ProMariner 44021 Battery Chargers ProSportHD 20 Plus Gen 4 - 20 Amp - 3 Bank Battery Charger ProSportHD Generation 4 boasts a tri-surface heatsink design. This heavy-duty lightweight design delivers significantly faster charging through optimal cooling while delivering true-rated amp output during charge mode.  ProSportHD's enhanced microprocessor and software provide digital features including a fuel gauge style Charge Completion Monitor, Charge Mode, individual Fault indicators, and three digitally selectable performance charge profiles for Flooded (lead acid), AGM, and GEL batteries. HP AGM profile on ProSportHD 20 Dual only.  Fully automatic 5-stage charging enhances battery performance while extending battery life. System Check OK and Battery Status indicators provide real-time installation and battery fault status.  Designed for use in harsh environments with our industrial-grade jacketed DC and AC power cables which include molded strain reliefs and wire splitters.  Features: ProMar Digital Technology Microprocessor and software-controlled charging technology for fast, precise charging Distributed-On-Demand™ Technology 100% of all available charging amps are utilized by distributing unused charging amps to any one or combination of all batteries as needed Heavy Duty Tri-Surface Extruded Heat Sink Design Upper, lower, and rear-facing heat sink design for optimal cooling while delivering true rated constant current charging amps during its two charge mode Expanded LED Display with Completion Status Gauge LED fuel gauge style completion status. Four-color multi-stage mode LED status bar. Multi-stage Charge Mode, System Check OK, individual Battery Status, and Battery Type indication Lightweight Design Up to 40% lighter compared to an epoxy-filled charger Auto-Maintain Energy Saver Mode Monitor and auto-maintain batteries only when needed to maintain a full state of charge. This significantly reduces AC power consumption Fully Automatic 5-Stage Digital Performance Charging 5 Stages: Analyzes, charges, conditions, auto maintains, and reconditions batteries once a month during storage periods. Fully charges and extends battery life Built-in Quality and Safety Dual inline waterproof fuses, reverse polarity, over-temperature, over-current, over-voltage, and ignition protection. Certified to Marine UL 1236. CEC and DOE listed. FCC Class B Easy Installation and Operation Pre-wired with 6’ AC and DC cables Battery Type: Group 24–31 Flooded, AGM, HP AGM, and GEL batteries 3 Year Warranty In the box: ​​Charger with 6' leads for 3 batteries Instructions with 4 small installation screws   WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 44021UPC Code: 031669440210

ProMariner 51300 Battery ChargersNo need to cut, strip or splice wires! Mount in an easy-to-reach location for safe AC power cord connection. Watertight and UV resistant cover. Converts plug holder to an AC inlet for ProMariner engineered chargers No cutting, stripping, or rewiring of AC power cord Watertight and UV resistant cover Easy to reach safe AC power cord connections Stainless steel mounting screws included Normalized SKU: 51300UPC Code: 316695130060

Newmar PT-24-13W Battery Chargers"Three Stage "Smart" Chargers Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any application from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life. A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries' ambient temperature. All models are housed in a rugged stainless steel case with a durable white powder coat finish, and the internal circuitry is polyurethane coated for maximum corrosion resistance. Features "Smart" circuitry provides three stage charging?bulk, absorption, float. Wide model range covers battery system ratings from 14-950 amp-hours Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages. Multiple isolated output banks; ammeter indicates total output current. (except PT-7) Optional sensor adjusts output voltage based on battery temperature. (except PT-7) Current limiting-prevents damage from overloading. Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel. Use as a power supply; can power loads without a battery in line. Built to last?rugged stainless steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry. Numerous Safety and EMC CompliancesTwo year parts and labor warranty Models   12 Volt 24 Volt 32 Volt PT-7 PT-24-8W PT-32-25W PT-14W PT-24-13W   PT-25W PT-24-20U   PT-40U PT-24-45U   PT-80 PT-24-60W     PT-24-95U   Detailed specifications below.  Specifications   12 Volt Models PT-7 PT-14W PT-25W PT-40W PT-80 Input VAC (50-60 Hz.) 88-132 or 176-264 85-264 90-132 or 180-264 85-135 or 170-270 90-264 Input Amps @ Full Load   @ 115 VAC 2 2.8 6.5 8.5 12 @ 230 VAC 1 1.4 4 4.3 7 P.F. Rating >.65 .93@230V .98@115V .7 .7 .95@230V .98@115V Max Output Amps 7 14 25 40 80 Output Banks 2 3 3 3 3 Battery Capacity (Amp-Hours) 14-70 28-140 50-250 80-400 160-800 Operating Temp. Rating Reference T-1 T-2 T-4 T-5 T-7 Case Size Ref. A-1 A-2 A-2 A-3 A-5 Weight; Lbs./Kg. 3.2/1.5 8/4 8.2/4 12/6 15.2/7 Optional Temp.Sensor Model N/A TCS-12/24 TCS-12/24 TCS-12/24 TCS-12/24 Remote Panel Model N/A RP RP RP RP Equalize Option No Yes Yes Yes Yes Output Indicator Ref. M-1 M-3 M-3 M-3 M-3 Compliance Ref. CG, CE CG, CE CG CG, CE CE    24 Volt Models PT-24-8W PT-24-13W PT-24-20U PT-24-45U PT-24-60W PT-24-95U Input VAC (50-60 Hz.) 85-264 90-132 or 180-264 85-135 or 170-270 90-264 207-253 90-264 Input Amps @ Full Load   @ 115 VAC 2.8 6.5 8.5 12 NA 26 @ 230 VAC 1.4 4 4.3 7 13 14 P.F. Rating .93@230V .98@115V .7 .7 .95@230V .98@115V .7 .95@230V .98@115V Max Output Amps 8 13 20 45 60 95 Output Banks 3 3 3 3 3 3 Battery Capacity (Amp-Hours) 16-80 26-130 40-200 90-450 120-600 180-950 Operating Temp. Rating Reference T-2 T-3 T-5 T-8 T-6 T-8 Case Size Ref. A-2 A-2 A-3 A-5 A-6 A-6 Weight; Lbs./Kg. 8/4 8.2/4 12/6 12.2/6 24.1/11 24.5/11 Optional Temp.Sensor Model TCS-12/24 TCS-12/24 TCS-12/24 TCS-12/24 TP TCS-12/24 Remote Panel Model RP RP RP RP N/A RP Equalize Option Yes Yes Yes Yes No Yes Output Indicator Ref. M-3 M-3 M-3 M-3 M-2 M-3 Compliance Ref. CG, CE CG CG, CE EN, CE EN, CE EN, CE   32 Volt Model  PT-32-25W Input VAC (50-60 Hz.) 104-126 Input Amps @ Full Load    @ 115 VAC 15 @ 230 VAC N/A P.F. Rating .7 Max Output Amps 25 Output Banks 3 Battery Capacity (Amp-Hours) 50-250 Operating Temp. Rating Reference T-6 Case Size Ref. A-4 Weight; Lbs./Kg. 12.2/6 Optional Temp.Sensor Model TP Remote Panel Model N/A Equalize Option No Output Indicator Ref. M-2 Compliance Ref. EN, CE Case Size     Inches Centimeters Ref H W D H W D A-1 10.5 5.0 2.8 26.7 12.7 7.1 A-2 12.5 7.7 4.3 31.8 19.6 10.9 A-3 13.85* 9.5 4.8* 35.2* 24.1 12.2* A-4 13.8A 9.8 5A 35A 24.9 12.7A A-5 14.8B 9.6 5.6B 37.6B 24.4 14.2B A-6 17.5C 12 7.2C 44.5C 30.5 18.3C * Add .75" (1.9 cm) to height and 1.35" (3.4 cm) to depth A Add 1.27" (3.2 cm) to height and 1.1" (2.8 cm) to depth B Add 1" (2.54 cm) to height and .5" (1.27 cm) to depth C Add 2" (5.08 cm) to height and 1" (2.54 cm) to depth Temperature Rating References:   T-1 -10°C to +45°C; Derate linearly from 100% @ 0°C to 80% @ -10°C T-2 -10°C to +60°C; Derate linearly from 100% @ 40°C to 60% @ 60°C T-3 -10°C to +60°C; Derate linearly from 100% @ 50°C to 60% @ 60°C T-4 -10°C to +60°C; Derate linearly from 100% @ 40°C to 60% @ 60°C T-5 -40°C to +60°C; Derate linearly from 100% @ 50°C to 75% @ 60°C T-6 -20°C to +50°C; Full output T-7 -20°C to +70°C; Derate linearly from 100% @ 45°C to 50% @ 70°C T-8 -20°C to +70°C; Derate linearly from 100% @ 50°C to 50% @ 70°C Output Indicator References   M-1 Total output ammeter M-2 Charge/Float L.E.D. M-3 Total output ammeter and charger status L.E.D.'s/Alarms Compliance References* See matrix for applicable models CG USCG CFR 183.410 (Ignition protected) EN EN 60335-1, EN 60335-2-29 CE Carries the CE Mark * Numerous other Safety and EMC compliances may also apply. Contact factory if further compliance   information is required. Nominal Output Voltages at Gel/Flooded Switch Settings (Without Temperature Compensation option installed or at 22.2˚C (72˚F) with Temperature Compensation option installed.)     12 Volt Models 24 Volt Models 32 Volt Model Charge Float Charge Float Charge Float Setting @ 50% load @ .5 amp load @ 50% load @ .5 amp load @ 50% load @ .5 amp load Gel-Cell 14.0 VDC 13.6 VDC 28.0 VDC 27.2 VDC 37.3 VDC 36.2 VDC Flooded/AGM 14.2 VDC 13.4 VDC 28.4 VDC 26.8 VDC 37.8 VDC 35.7 VDC "Normalized SKU: PT2413WUPC Code: 445-4869-0

Dual Pro RS3 Battery ChargersRealPRO Series Battery Charger - 18A - 3-6A-Banks - 12V-36VRealPro Series battery chargers (formerly Recreation Series) are an affordable, reliable and safe battery charging system designed for everyday use. The system is engineered for users who need a charging system on an occasional basis and may not want or need the capabilities of a heavier duty and higher amperage product.It is designed for use in many types of applications including bass boats, runabouts, pontoon boats, other watercraft, automobiles, ATVs, golf carts and other similar uses. The system delivers sophisticated capabilities and superior value to customers.Battery Charging Systems Designed for Everyday Applications Affordable, Reliable and Safe Unmatched Performance, Reliability, Safety and Quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 of Our Satisfied Customers! Wide Variety of Applications Universal Input (100-240 VAC 50/60HZ) Features: Approved for Wet Cell and Absorbed Glass Mat (AGM) batteries Designed for use in fresh and salt water Dependable, rugged construction and waterproof Independent outputs and fully automatic Battery maintenance mode Two year warranty DC charge cables = 5ft and AC power cord = 3ft Approved and meets ISO 8846 Marine standards Models available to charge 12-24V systems LED lights indicate “Each Battery’s” state of charge Reverse polarity protected and no installation restrictions Ignition protected (US Coast Guard 33 CFR 183.410) FCC 15 Parts A and B Interference Compliant May be used in many types of sporting applications including: Bass Boats Runabouts Pontoons Automobiles ATVs Golf Carts… Specifications:Amps - Output = 18 Amps Per Bank = 6 Banks = 3 Battery Type = NONE Charger Type = NONE Portable = NONE Voltage - Charger Input = NONE Voltage - Output (Volts) = 12-36VNormalized SKU: RS3UPC Code: 738562000557

  Download LiteratureGuest-Marinco 2711A Battery ChargersOn-Board Battery Charger 10A / 12V - 2 Bank - 120V InputGuest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.Features: All high frequency, digital charging technology Fully automatic 5-stage performance charging Dedicated battery charging, sensing and control per bank Expanded LED charge status monitor Wiring and battery fault detection Auto-maintain energy saver mode Up to 40 percent lighter 100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications All models are pre-wired for easy installation For all 12 volt flooded and AGM lead acid batteries Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection. 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Amps - Output = 10 Amps Per Bank = 5 Banks = 2 Battery Type = NONE Charger Type = NONE Portable = NONE Voltage - Charger Input = 120V Voltage - Output (Volts) = NONENormalized SKU: 2711AUPC Code: 046904904112Guest-Marinco 2711A Literature Download  Owners Manual  Product Brochure

  Download LiteratureGuest-Marinco 2710A Battery ChargersOn-Board Battery Charger 10A / 12V - 1 Bank - 120V InputGuest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.Features: All high frequency, digital charging technology Fully automatic 5-stage performance charging Dedicated battery charging, sensing and control per bank Expanded LED charge status monitor Wiring and battery fault detection Auto-maintain energy saver mode Up to 40 percent lighter 100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications All models are pre-wired for easy installation For all 12 volt flooded and AGM lead acid batteries Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection. 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Amps - Output = 10 Amps Per Bank = 10 Banks = 1 Battery Type = NONE Charger Type = NONE Portable = NONE Voltage - Charger Input = 120V Voltage - Output (Volts) = NONENormalized SKU: 2710AUPC Code: 046904904105Guest-Marinco 2710A Literature Download  Owners Manual  Product Brochure

  Download LiteratureGuest-Marinco 2713A Battery ChargersOn-Board Battery Charger 15A / 12V - 3 Bank - 120V InputGuest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.Features: All high frequency, digital charging technology Fully automatic 5-stage performance charging Dedicated battery charging, sensing and control per bank Expanded LED charge status monitor Wiring and battery fault detection Auto-maintain energy saver mode Up to 40 percent lighter 100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications All models are pre-wired for easy installation For all 12 volt flooded and AGM lead acid batteries Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection. 2 year warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Amps - Output = 15 Amps Per Bank = 5 Banks = 3 Battery Type = NONE Charger Type = NONE Portable = NONE Voltage - Charger Input = 120V Voltage - Output (Volts) = NONENormalized SKU: 2713AUPC Code: 046904904129Guest-Marinco 2713A Literature Download  Owners Manual  Product Brochure

  Download LiteratureSamlex America SEC-2425UL Battery Chargers25A Battery Charger - 24V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp SensorThis advanced fully automatic three-stage 25 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit, reverse polarity and thermal overload protection. The unit allows charging of up-to 2 separate battery banks.Features: Switch mode technology for high efficiency, lightweight and quiet operation Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell Can charge 2 banks of batteries simultaneously, no isolator necessary Can be used as a power supply or DC UPS when used in conjunction with a battery User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries “Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries Voltmeter and Ammeter for monitoring Fan cooled based on output current Protections: Short circuit, overload, reverse battery connection and over temperature Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively Specifications: Input: 120 VAC or 230 VAC Output: 24 VDC Amps: 25 Remote Control: 900-RC Weight: 9 (lbs) Weight: 4.1 (kg) Dimensions: 13.03 x 9.6 x 3.82 (in) Dimensions: 331 x 244 x 97 (mm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Test bench Automotive Marine Communications sites Battery back-up systems Hobby WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Amps - Output = 25A Amps Per Bank = 12.5A Banks = 2 Battery Type = NONE Charger Type = NONE Portable = NONE Voltage - Charger Input = NONE Voltage - Output (Volts) = 24VNormalized SKU: SEC2425ULUPC Code: 622988083068Samlex America SEC-2425UL Literature Download  Owners Manual  Product Brochure

ProMariner 52060 Battery ChargersProTournament RemoteTri-color charge mode status.Cable length: 12'WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Normalized SKU: 52060UPC Code: 031669520608

Attwood Marine 11901-4 Battery ChargersBattery ChargerAttwood's Battery Charger is compact and perfect for your bench, garage or shop use. Overcharge, short circuit and reverse polarity protection provides years of worry free use. Provides 2 and 6 amp charge for 12V batteries. 6 amp charge for 6V batteries. Automatically switches to trickle charge mode after battery is fully charged. Dual rated 12 and 6 volt battery charger can be used for all of your marine, automotive, RV and sports applications. LED indicator - power on Ammeter indicates charging current 6 foot power cord length 48 inch battery connector leads WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Amps - Output = 6 Banks = NONE Battery Type = NONE Charger Type = NONE Portable = NONE Voltage - Charger Input = NONE Voltage - Output (Volts) = 12VNormalized SKU: 119014UPC Code: 022697119018

  Download LiteratureProMariner 63140 Battery ChargersAll Digital Electronic ChargingIndustry recognized with the 2010 IBEX Innovation Award, ProNauticP employs our ProMar Digital Performance Charging Platform which combines all digital control and software-based power conversion technology with global energy management features. ProNauticP addresses the trend of incorporating and using more 12-volt electronics on-board today's power, sail, cruising and sport fishing boats. Boasting twelve digitally-controlled performance charging profiles with finger tip selection, ProNauticP fully charges, conditions, maintains and re-conditions batteries while extending battery life and maximizing battery reserve power performance. ProNauticP is Power Factor Corrected with auto-ranging global AC input allowing all models to operate off a standard household power connection. Featuring dual digital displays for real-time display of actual charging voltage and amperage and AC power-on diagnostics with pass or fail status in addition to discreet fault indication for mis-wiring or adverse battery bank conditions. Designed to provide more time on the water enjoying what you like most... boating.ProMar Digital Performance ChargingProMar Digital Charging Performance - 12 Selectable ProfilesUp to 12 performance & precision 4-stage charging profiles: Charge, Condition, Maintain and Re-condition. Automatic dockside power mode for 12 Volt DC lighting and appliances. Factory set for Flooded (Lead Acid) batteries. AGM, GEL selectable.Power Factor Correction - Global AC InputAuto-ranging (100-250VAC/50-60Hz) global AC input with reduced harmonic distortion allowing all models to operate off a household power outlet connection. ProNauticP consumes less power so more AC power is available on board.Distributed On Demand TechnologyAutomatically senses and distributes 100% of available charging amps to any one bank or combination of all banks.Digital Self-Calculating Absorption and Battery Health Re-Conditioning ModeAutomatically programs conditioning time based on discharge state of batteries. Automatically de-sulfates batteries after 21 days in the maintain mode, improving reserve power performance & extending battery life.Conservation Energy Saver ModeAfter 72 hours of not seeing a load greater than 5 amps, float voltage will be lowered consuming less energy during storage periods. (for flooded & sealed charge profiles) Service and Fault Mode LED IndicatorsReal time indication of wiring faults or adverse conditions that may impact the operation of a boat's charging system.Automatic Fan Speed ControlQuiet operation. Innovative front exhaust prevents restriction of air flow and cooling.Automatic Temperature Compensation and Built-in SafetyRemote temperature probe included - Ignition protected and current limiting. Designed and constructed to: Marine ULc 1236, CE, CTick and FCC Class B.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Voltage - Charger Input = 100-240 Portable = NONE Amps - Output = 40 Voltage - Output (Volts) = 12 Banks = 3 Battery Type = NONE Charger Type = NONENormalized SKU: 63140UPC Code: 031669631403ProMariner 63140 Literature Download  Owners Manual

  Download LiteratureBlue Sea System 7622 Battery Chargers7622Manual Control: YesCoil Voltage: 12vFeatures: Manual control switch provides an added level of safety allowing control with or without power, and offering "Locked Off" capability for servicing Includes ML-Series Remote Control Contura Switch PN 2146 500 Ampere continuous rating Magnetic Latch (ML)-ACR draws very low current (<10 mA to monitor terminal voltage) in the "ON" or "OFF" states, and draws moderate current for very short time when changing state Start Isolation (SI)-Can be configured for temporary isolation of House loads from Engine circuit during engine cranking to protect sensitive electronics Engine Isolation (EI)-Can be configured for isolation of two engines while both are running to protect engine electronics and maximize alternator output Senses charging on two battery banks Supports high-output alternators up to 500 Amps LED output to remotely indicate when batteries are combined, isolated, in voltage lockout, in Start or Engine isolation 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance 7/8" (22mm) stud length accepts multiple cable terminals Label recesses for circuit protection Silver alloy contacts provide high reliability for switching live loads WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:Lockable = NONE AFD = NONE Positions = NONE Amps - Max = NONEBLUE SEA 7622 ML SERIES HEAVY DUTY CHARGING RELAY W/ MANUAL CONTROLNormalized SKU: 7622UPC Code: 632085076221Blue Sea System 7622 Literature Download  Owners Manual