Ice Eater P500.025.615 Ice Eaters The Ice Eater P500.025.615 is a 0.5 HP, 230V de-icing unit with a 25-foot power cord. This is the shortest cord configuration in the P500 lineup, built for installations where the 230V power source is right at the dock edge and a longer cord would just be extra cable to coil up and manage all winter. The P500 series prevents ice formation through water circulation. A 12-inch propeller draws warmer water up from below the thermocline and pushes it outward along the surface, keeping the waterline clear without a heating element. That means lower operating costs and no element to burn out or replace mid-season. The motor is totally enclosed and thermally protected for continuous unattended operation. The housing is UV-stabilized polyethylene that handles sun exposure, salt air, and freeze-thaw cycling without issue. A stainless steel hanging bracket and propeller guard are included, so installation is straightforward right out of the box. Motor: 0.5 HP, 230V, 60 Hz, single-phase Cord length: 25 feet Propeller diameter: 12 inches Effective de-icing radius: up to 75 feet in diameter depending on water depth and temperature Motor housing: UV-stabilized polyethylene Includes: motor, 25-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 25-foot cord is the right fit when your pedestal or outlet is mounted directly on the dock structure and you want a clean, minimal install. If your power source is further away, the P500 series is also available with 50-foot, 100-foot, and 150-foot cord options in both 115V and 230V configurations. Normalized SKU: P500025615

Ice Eater P500.025 Ice Eaters The Ice Eater P500.025 is a 0.5 HP, 115V de-icing unit with a 25-foot power cord. It is the shortest cord option in the 115V P500 lineup, designed for setups where a standard outlet is mounted right at the dock and you just need enough cord to reach the water without a tangle of extra cable sitting on the dock all winter. The P500 series keeps ice from forming through water circulation rather than heat. A 12-inch propeller pulls warmer water up from below the surface and pushes it outward along the waterline, breaking the conditions ice needs to set up. No heating element means no element failures and lower power draw over a long season. The motor is totally enclosed and thermally protected for continuous outdoor operation. The UV-stabilized polyethylene housing resists sun degradation and handles freeze-thaw cycling without cracking. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang straight out of the box. Motor: 0.5 HP, 115V, 60 Hz, single-phase Cord length: 25 feet Propeller diameter: 12 inches Effective de-icing radius: up to 75 feet in diameter depending on water depth and temperature Motor housing: UV-stabilized polyethylene Includes: motor, 25-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 25-foot cord works well when your 115V outlet is already on the dock structure and the slip is compact. If you need more reach, the P500 is also available in 100-foot and 150-foot cord lengths on 115V, and in 25-foot, 50-foot, and 100-foot lengths on 230V. Normalized SKU: P500025

Ice Eater P250.200.615 Ice Eaters The Ice Eater P250.200.615 is a 0.25 HP, 230V de-icing unit with a 200-foot power cord. The P250 is the lighter-duty model in the Ice Eater lineup, sized for smaller slips, single boat lifts, and situations where you need ice protection but do not need the full output of the 0.5 HP P500 series. The 200-foot cord gives you a long reach from the power source to the water, making it a practical choice for docks where the 230V pedestal is set well back from the slip. Like the rest of the Ice Eater line, the P250 works through water circulation rather than heat. A propeller draws warmer water up from below the surface and moves it outward along the waterline, preventing ice from forming around your hull, pilings, and dock structure. No heating element means no element burnout and lower operating costs through the winter months. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The housing is UV-stabilized polyethylene that holds up to sun, salt air, and freeze-thaw cycling season after season. A stainless steel hanging bracket and propeller guard are included in the box. Motor: 0.25 HP, 230V, 60 Hz, single-phase Cord length: 200 feet Motor housing: UV-stabilized polyethylene Includes: motor, 200-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The P250 is a good fit for smaller protected slips where ice pressure is a concern but the exposure level does not call for a larger unit. If you are dealing with a more exposed location, heavy current, or a larger slip, the 0.5 HP P500 series handles those conditions better. The 200-foot cord on this model covers long dock runs where the power source is far from the water. Normalized SKU: P250200615

Ice Eater P250.150.615 Ice Eaters The Ice Eater P250.150.615 is a 0.25 HP, 230V de-icing unit with a 150-foot power cord. It sits in the middle of the P250 cord length range, giving you a solid reach from a 230V pedestal to the water without going all the way to the 200-foot option. A good fit for single slips, boat lifts, and smaller dock sections on 230V service where the power source is a moderate distance from the slip. The P250 uses the same propeller-driven circulation approach as the rest of the Ice Eater lineup. Warmer water from below the surface gets pulled up and pushed outward along the waterline, keeping ice from forming around your hull, dock pilings, and structure. No heating element in the design means lower operating costs and nothing to burn out over a long winter. The motor is totally enclosed and thermally protected for continuous unattended outdoor use. The UV-stabilized polyethylene housing handles sun exposure, salt air, and repeated freeze-thaw cycles without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang right out of the box. Motor: 0.25 HP, 230V, 60 Hz, single-phase Cord length: 150 feet Motor housing: UV-stabilized polyethylene Includes: motor, 150-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 150-foot cord covers most mid-range dock runs on 230V service. If your power source is closer to the water, the P250 is also available with 25-foot, 50-foot, and 100-foot cords. For larger slips or more exposed locations, the 0.5 HP P500 series handles heavier ice conditions. Normalized SKU: P250150615

Ice Eater P250.150 Ice Eaters The Ice Eater P250.150 is a 0.25 HP, 115V de-icing unit with a 150-foot power cord. It runs on standard 115V shore power and gives you 150 feet of reach from the outlet to the water, which covers most single-slip dock setups without needing an extension cord or additional wiring. The P250 keeps ice at bay through water circulation. A propeller draws warmer water up from below the surface and pushes it outward along the waterline, disrupting ice formation around your hull, dock pilings, and boat lift structure. The 0.25 HP motor is sized for smaller, more protected slips where you need reliable ice prevention without the output of the larger P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing holds up to sun, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang straight out of the box. Motor: 0.25 HP, 115V, 60 Hz, single-phase Cord length: 150 feet Motor housing: UV-stabilized polyethylene Includes: motor, 150-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 150-foot cord on 115V service is a practical choice for docks where the nearest standard outlet is set back from the water. If your dock runs 230V pedestals, the P250 is also available in 230V configurations with matching cord length options. For larger slips or more exposed locations with heavier ice conditions, the 0.5 HP P500 series is the step up. Normalized SKU: P250150

Ice Eater P250.100.615 Ice Eaters The Ice Eater P250.100.615 is a 0.25 HP, 230V de-icing unit with a 100-foot power cord. It is a practical mid-range option in the P250 lineup for docks running 230V service, giving you enough cord to reach most standard slip configurations from a pedestal without going to a longer cord than you actually need. The P250 prevents ice formation through water circulation rather than heat. A propeller draws warmer water up from below the surface and pushes it outward along the waterline, keeping ice from taking hold around your hull, pilings, and dock structure. The 0.25 HP motor is sized for smaller, more sheltered slips where steady ice prevention matters but the conditions do not call for the heavier output of the P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing resists sun degradation, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang right out of the box. Motor: 0.25 HP, 230V, 60 Hz, single-phase Cord length: 100 feet Motor housing: UV-stabilized polyethylene Includes: motor, 100-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 100-foot cord on 230V covers most mid-length dock runs where the pedestal is set back from the slip but not at the far end of a long dock. The P250 is also available in 25-foot, 50-foot, 150-foot, and 200-foot cord lengths for 230V installations, and in 115V configurations if your dock runs standard shore power. For larger slips or heavier ice exposure, the 0.5 HP P500 series is the next step up. Normalized SKU: P250100615

Ice Eater P250.100 Ice Eaters The Ice Eater P250.100 is a 0.25 HP, 115V de-icing unit with a 100-foot power cord. It runs on standard 115V shore power and gives you a solid 100 feet of reach from the outlet to the water, covering most single-slip setups without needing an extension cord or any rewiring at the dock. The P250 works by circulating water rather than heating it. A propeller draws warmer water up from below the surface and moves it outward along the waterline, preventing ice from forming around your hull, dock pilings, and boat lift components. The 0.25 HP motor is the right size for smaller, more sheltered slips where consistent ice prevention is the goal and the conditions do not demand the heavier output of the P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing handles sun exposure, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang right out of the box. Motor: 0.25 HP, 115V, 60 Hz, single-phase Cord length: 100 feet Motor housing: UV-stabilized polyethylene Includes: motor, 100-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 100-foot cord on 115V is a versatile fit for docks where the outlet is set back from the slip but not at the far end of a long run. The P250 is also available in 25-foot and 150-foot cord lengths on 115V, and in 230V configurations if your dock pedestal runs higher voltage. For larger slips or more exposed locations, the 0.5 HP P500 series handles heavier ice conditions. Normalized SKU: P250100

Ice Eater P250.050.615 Ice Eaters The Ice Eater P250.050.615 is a 0.25 HP, 230V de-icing unit with a 50-foot power cord. It is a clean fit for compact dock setups on 230V service where the pedestal is close to the slip and a shorter cord keeps the install tidy. No extra cord to coil up, no cable management headaches through the winter. The P250 prevents ice formation through water circulation. A propeller draws warmer water up from below the surface and pushes it outward along the waterline, keeping ice from forming around your hull, pilings, and dock structure. The 0.25 HP motor is sized for smaller, more sheltered slips where reliable ice prevention is the priority and the exposure level does not call for the heavier output of the P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing holds up to sun, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang straight out of the box. Motor: 0.25 HP, 230V, 60 Hz, single-phase Cord length: 50 feet Motor housing: UV-stabilized polyethylene Includes: motor, 50-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 50-foot cord is the middle option in the shorter end of the P250 230V range. If your power source is right at the dock edge, the 25-foot cord keeps things even cleaner. If you need more reach, the P250 is also available in 100-foot, 150-foot, and 200-foot cord lengths on 230V. For larger slips or heavier ice conditions, the 0.5 HP P500 series is the step up. Normalized SKU: P250050615

Ice Eater P250.050 Ice Eaters The Ice Eater P250.050 is a 0.25 HP, 115V de-icing unit with a 50-foot power cord. It runs on standard 115V shore power and is sized for compact dock setups where the outlet is reasonably close to the water. Fifty feet is enough cord to reach most single slips from a dock-mounted outlet without any extra cable piling up on the dock. The P250 keeps ice from forming through water circulation rather than heat. A propeller draws warmer water up from below the surface and pushes it outward along the waterline, disrupting ice formation around your hull, pilings, and boat lift structure. The 0.25 HP motor is the right fit for smaller, more sheltered slips where steady ice prevention is the goal without the output of the larger P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing resists sun degradation, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang straight out of the box. Motor: 0.25 HP, 115V, 60 Hz, single-phase Cord length: 50 feet Motor housing: UV-stabilized polyethylene Includes: motor, 50-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 50-foot cord sits between the 25-foot and 100-foot options in the 115V P250 range, making it a good middle ground for slips where the outlet is close but not right at the water's edge. If your dock runs 230V pedestals, the P250 is also available in matching 230V configurations. For larger slips or more exposed locations with heavier ice pressure, the 0.5 HP P500 series is the next step up. Normalized SKU: P250050

Ice Eater P250.025.615 Ice Eaters The Ice Eater P250.025.615 is a 0.25 HP, 230V de-icing unit with a 25-foot power cord. It is the shortest cord option in the P250 230V lineup, built for installations where the 230V pedestal or outlet is mounted directly on the dock structure and the slip is right there. No excess cord, no tangles, just a clean hang and done. The P250 prevents ice formation through water circulation rather than heat. A propeller draws warmer water up from below the surface and pushes it outward along the waterline, keeping ice from forming around your hull, dock pilings, and boat lift components. The 0.25 HP motor is sized for smaller, more sheltered slips where consistent ice prevention matters and the conditions do not call for the heavier output of the P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing handles sun exposure, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang right out of the box. Motor: 0.25 HP, 230V, 60 Hz, single-phase Cord length: 25 feet Motor housing: UV-stabilized polyethylene Includes: motor, 25-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 25-foot cord is the right call when your 230V outlet is already at the dock edge and you want the cleanest possible install. If you need more reach, the P250 is also available in 50-foot, 100-foot, 150-foot, and 200-foot cord lengths on 230V, and in 115V configurations for standard shore power setups. For larger slips or heavier ice exposure, the 0.5 HP P500 series handles those conditions. Normalized SKU: P250025615

Ice Eater P250.025 Ice Eaters The Ice Eater P250.025 is a 0.25 HP, 115V de-icing unit with a 25-foot power cord. It is the shortest cord option in the 115V P250 lineup, designed for dock setups where a standard outlet is mounted right at the slip and you just need enough cord to drop the unit into the water. Clean install, minimal cord management, and ready to run all winter. The P250 works by circulating water rather than heating it. A propeller draws warmer water up from below the surface and pushes it outward along the waterline, preventing ice from forming around your hull, dock pilings, and boat lift structure. The 0.25 HP motor is sized for smaller, more sheltered slips where consistent ice prevention is the goal without the output of the larger P500 series. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing handles sun exposure, salt air, and freeze-thaw cycling without cracking or fading. A stainless steel hanging bracket and propeller guard are included, so the unit is ready to hang straight out of the box. Motor: 0.25 HP, 115V, 60 Hz, single-phase Cord length: 25 feet Motor housing: UV-stabilized polyethylene Includes: motor, 25-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The 25-foot cord is the right pick when your 115V outlet is already on the dock structure and the slip is compact. If you need more reach on 115V, the P250 is also available in 50-foot and 100-foot cord lengths. The P250 is also offered in 230V configurations for docks running higher voltage pedestals. For larger slips or more exposed locations, the 0.5 HP P500 series handles heavier ice conditions. Normalized SKU: P250025

Ice Eater P1000.400.615 Ice Eaters The Ice Eater P1000.400.615 is a 1 HP, 230V de-icing unit with a 400-foot power cord. This is the top of the Ice Eater lineup in terms of motor output, built for large marina slips, commercial docks, wide waterfront structures, and any situation where the smaller P250 or P500 units simply do not have enough reach or circulation capacity to get the job done. The P1000 uses the same propeller-driven water circulation approach as the rest of the Ice Eater line, scaled up significantly. A larger propeller pulls warmer water up from below the thermocline and pushes it outward along the surface, clearing a substantial zone around your dock, pilings, and hull. The 400-foot cord gives you the longest reach in the lineup, covering large commercial dock runs where the power source is far from the water. The motor is totally enclosed and thermally protected for continuous unattended outdoor operation. The UV-stabilized polyethylene housing holds up to sun, salt air, and repeated freeze-thaw cycles without cracking or fading. A stainless steel hanging bracket and propeller guard are included in the box. Motor: 1 HP, 230V, 60 Hz, single-phase Cord length: 400 feet Motor housing: UV-stabilized polyethylene Includes: motor, 400-foot power cord, stainless steel hanging bracket, and propeller guard Rated for continuous duty operation Thermally protected motor The P1000 is the right choice for large exposed slips, wide marina bays, commercial waterfront structures, and anywhere that ice pressure is a serious seasonal concern. The 230V configuration pairs with 240V marina pedestals and commercial shore power setups. If your application is smaller or your power source is 115V, the P250 and P500 series cover those needs at lower output levels. Normalized SKU: P1000400615

Ice Eater P1000.350.615 Ice Eaters The Ice Eater P1000 is a 1 HP de-icer built for serious winter dock protection. Running on 230V single-phase power, this unit circulates warmer water from the bottom up to keep ice from forming around your dock, pilings, and hull. It's not magic — it's thermodynamics, and it works. This complete package includes 350 feet of cord, so you've got plenty of reach from your power source to the water without splicing or extension cords. The motor is fully submersible and enclosed in a corrosion-resistant housing designed to hold up in both fresh and salt water environments. Key Specs Motor: 1 HP Voltage: 230V, single-phase Cord Length: 350 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The P1000 hangs vertically in the water column, angled to push a continuous column of warmer bottom water toward the surface. Most installs use the included hanging bracket and rope system to position the unit 2 to 4 feet below the surface, though depth can be adjusted based on your specific conditions. This is a complete unit — motor, prop guard, and 350' cord included. No additional cord kit needed. Normalized SKU: P1000350615

Ice Eater P1000.300.615 Ice Eaters The Ice Eater P1000 is a 1 HP de-icer that keeps your dock, pilings, and hull clear of ice all winter long. It runs on 230V single-phase power and works by pulling warmer water up from the bottom of the water column to the surface, disrupting ice formation before it becomes a problem. This complete package comes with 300 feet of cord, giving you a solid run from your power source to the water without needing extension cords or additional cord kits. The motor is fully submersible and housed in a corrosion-resistant casing built to handle both fresh and salt water without complaint. Key Specs Motor: 1 HP Voltage: 230V, single-phase Cord Length: 300 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water Installation is straightforward. The unit hangs vertically in the water, typically positioned 2 to 4 feet below the surface using the included hanging bracket and rope system. Depth can be adjusted based on your dock layout and local conditions. If 300 feet of cord covers your run, this is the same proven P1000 motor as the longer-cord variants, just packaged for shorter dock setups. Everything you need is in the box. Normalized SKU: P1000300615

Ice Eater P1000.250.615 Ice Eaters The Ice Eater P1000 is a 1 HP submersible de-icer designed to protect your dock, boat, and pilings through the winter months. It runs on 230V single-phase power and works by circulating warmer water from the bottom of the water column up to the surface, keeping ice from forming where it matters most. This complete package includes 250 feet of cord. That covers most standard dock setups without needing extra cord or extension runs. If your power source is close to the water, this is a clean, no-fuss configuration. Key Specs Motor: 1 HP Voltage: 230V, single-phase Cord Length: 250 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The unit hangs vertically in the water column, typically 2 to 4 feet below the surface, using the included hanging bracket and rope system. Depth is adjustable depending on your dock layout and local water conditions. Same proven P1000 motor as the longer-cord variants, packaged for docks where 250 feet gets the job done. Everything needed for installation is included. Normalized SKU: P1000250615

Ice Eater P1000.200.615 Ice Eaters The Ice Eater P1000 is a 1 HP submersible de-icer built to keep ice from forming around your dock, hull, and pilings all winter. It runs on 230V single-phase power and circulates warmer water from the bottom of the water column up to the surface, where ice forms first. Simple physics, reliable results. This complete package includes 200 feet of cord. It's the shortest cord option in the P1000 lineup, making it a good fit for docks where the power source is close to the water's edge and a longer run would just be extra cord to manage. Key Specs Motor: 1 HP Voltage: 230V, single-phase Cord Length: 200 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The unit hangs vertically in the water, typically positioned 2 to 4 feet below the surface using the included hanging bracket and rope system. Depth is adjustable to suit your specific dock setup and water conditions. Same proven P1000 motor as the rest of the lineup, just packaged with 200 feet of cord for shorter dock configurations. Everything needed for installation is included in the box. Normalized SKU: P1000200615

Ice Eater P1000.150.615 Ice Eaters The Ice Eater P1000 is a 1 HP submersible de-icer that keeps ice from forming around your dock, hull, and pilings through the winter. It runs on 230V single-phase power and works by pulling warmer water up from the bottom of the water column to the surface, disrupting ice formation right where it starts. This complete package comes with 150 feet of cord. It's a great fit for compact dock setups or situations where the power source is right at the water's edge. Less cord to manage, same motor performance as the longer-cord variants in the P1000 lineup. Key Specs Motor: 1 HP Voltage: 230V, single-phase Cord Length: 150 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The unit hangs vertically in the water, typically 2 to 4 feet below the surface, using the included hanging bracket and rope system. Depth is adjustable based on your dock layout and local water conditions. Everything needed for installation is included. If 150 feet covers your run, this is a clean, right-sized package without paying for cord you won't use. Normalized SKU: P1000150615

Ice Eater P1000.150 Ice Eaters The Ice Eater P1000 is a 1 HP submersible de-icer that runs on standard 115V power, making it one of the more accessible options in the P1000 lineup. No special wiring or 230V service required. If you've got a standard 20-amp outlet near your dock, you're in business. It works the same way as every other Ice Eater: the motor pulls warmer water up from the bottom of the water column to the surface, keeping ice from forming around your dock, hull, and pilings. Straightforward thermodynamics that has been keeping docks clear for decades. This complete package includes 150 feet of cord, sized for compact dock setups where the power source is close to the water. Less cord to manage, same proven motor performance. Key Specs Motor: 1 HP Voltage: 115V, single-phase Cord Length: 150 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The unit hangs vertically in the water, typically 2 to 4 feet below the surface, using the included hanging bracket and rope system. Depth is adjustable to match your dock layout and local conditions. Everything needed for installation is included. If you need 230V variants or longer cord lengths, those are available separately in the P1000 lineup. Normalized SKU: P1000150

Ice Eater P1000.100.615 Ice Eaters The Ice Eater P1000 is a 1 HP submersible de-icer that runs on 230V single-phase power and keeps ice from forming around your dock, hull, and pilings all winter long. It circulates warmer water from the bottom of the water column up to the surface, where ice forms first. The process is continuous, quiet, and effective. This complete package includes 100 feet of cord, making it the shortest cord configuration in the 230V P1000 lineup. If your power panel or outlet is right at the dock, 100 feet is plenty and keeps things tidy. No excess cord to coil up and store at the end of the season. Key Specs Motor: 1 HP Voltage: 230V, single-phase Cord Length: 100 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The unit hangs vertically in the water, typically 2 to 4 feet below the surface, using the included hanging bracket and rope system. Depth is adjustable to suit your dock layout and local water conditions. Same proven P1000 motor as the rest of the lineup. If you need more cord, longer configurations are available in 150', 200', 250', 300', and 350' options. Everything needed for installation is included. Normalized SKU: P1000100615

Ice Eater P1000.100 Ice Eaters The Ice Eater P1000 is a 1 HP submersible de-icer that runs on standard 115V power. No special electrical service, no 230V wiring, no electrician required. If you have a standard 20-amp outlet near your dock, this unit is ready to go to work. It keeps ice from forming around your dock, hull, and pilings by continuously circulating warmer water from the bottom of the water column up to the surface. The process runs quietly in the background all winter, doing its job without any fuss. This complete package comes with 100 feet of cord, making it the most compact configuration in the 115V P1000 lineup. It's a natural fit for smaller docks or setups where the power source is close to the water. Short run, clean install. Key Specs Motor: 1 HP Voltage: 115V, single-phase Cord Length: 100 feet Propeller Diameter: 12 inches Effective Coverage Area: up to 7,500 sq. ft. (varies by water depth and temperature) Motor Housing: Corrosion-resistant, fully submersible Suitable for: fresh water and salt water The unit hangs vertically in the water, typically 2 to 4 feet below the surface, using the included hanging bracket and rope system. Depth is adjustable to match your specific dock layout and water conditions. If you need more cord, the 115V P1000 is also available with 150 feet. For longer runs or higher-amperage setups, the 230V variants cover cord lengths from 100' up to 350'. Everything needed for installation is included in the box. Normalized SKU: P1000100