Dexter Axle K71-G04-00 Brake Components Genuine Tie Down brake pad with galvanized backing Fits 46304 and 46901 Calipers Normalized SKU: K71G0400

Dexter Axle K99-184-24 Brake Components Complete Disc Brake Actuator The Dexter Axle K99-184-24 is a zinc-finish surge actuator kit rated at 8,400 lbs, built for single or tandem axle disc brake setups. At 14.5" in length, it's a top-mount, bolt-on unit designed to fit a wide range of trailer tongue configurations without modification. This is the XR-84 surge actuator, and its standout feature is the self-latching coupler developed by UFP. Lower the actuator onto a 2" ball, and the latch opens and closes around it automatically. No fumbling with manual latches at the ramp. The inner housing is interchangeable with any UFP actuator rated 8,400 lbs and below, which makes future repairs or swaps straightforward. The master cylinder is corrosion-resistant aluminum and tuned specifically for disc brake output pressure. The inner member contains all working components and can be fully removed for repair or replacement without pulling the entire unit. Outer housing mounting holes are spaced 3" apart and 3/4" down from the mounting surface, making it cross-compatible with other common actuator brands including Titan, Tie Down, and Demco. Rated capacity: 8,400 lbs; fits single and tandem axle disc brake applications Overall length: 14.5" Self-latching coupler; fits standard 2" ball Top-mount, bolt-on installation Mounting holes spaced 3" apart, 3/4" down from the mounting surface Cross-compatible with Titan, Tie Down, and Demco outer housings Corrosion-resistant aluminum master cylinder, tuned for disc brake pressure Inner member is fully removable for repair or replacement Zinc finish for corrosion resistance Normalized SKU: K9918424UPC Code: 876983005529

Dexter Axle K71-816-00 Brake Components Stainless Ventilated Rotor With Stainless Caliper Kit The Dexter Axle K71-816-00 is a complete disc brake kit built around a 12" ventilated rotor and stainless steel caliper, rated for 6,000 lb Legacy UFP axle applications. If you're upgrading or replacing a disc brake setup on a boat trailer, this kit gives you everything needed to get from bare spindle to fully functional brakes in one box. The rotor and caliper are stainless steel, which matters a lot in a saltwater or high-humidity environment where standard iron components start showing rust after a single season. The ventilated rotor design helps manage heat during repeated brake applications, which is exactly what happens when you're loading and unloading at a busy ramp. Hardware throughout the kit leans heavily on stainless: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless steel. The caliper body includes the piston and bracket, and a spacer bracket is included specifically for mounting on a Dexter Axle. Back plates on the brake pads add an extra layer of corrosion resistance where the pads contact the caliper. Fits: 12", 6,000 lb Legacy UFP disc brake applications 12" ventilated stainless steel rotor Stainless steel caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Spacer bracket included for Dexter Axle mounting Kit includes all hardware: hex bolts, copper washers, banjo fitting Normalized SKU: K7181600UPC Code: 876983006458

Dexter Axle K71-814-00 Brake Components Zinc+ Ventilated Rotor With Aluminum Caliper Kit The Dexter Axle K71-814-00 is a complete disc brake kit built around a 12" ventilated Zinc+ coated rotor and an aluminum caliper, rated for 6,000 lb Legacy UFP axle applications. It's the value-conscious option in the Dexter disc brake kit lineup, and it still brings solid corrosion protection to the table thanks to the Zinc+ finish on the rotor. Zinc+ is a conversion coating applied over zinc plating that delivers more than five times the corrosion resistance of standard zinc plating alone. For a freshwater trailer that sees regular use, that's meaningful protection without the price premium of a full stainless rotor. The 12" ventilated rotor design helps manage heat during repeated brake applications, keeping performance consistent whether you're making one run or several in a day. The aluminum caliper keeps the overall kit weight down while still providing reliable clamping force. Stainless steel is used throughout the hardware: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless. Brake pads include a corrosion-resistant back plate. A spacer bracket is included for mounting on a Dexter Axle, along with all necessary hardware to complete the installation. Fits: 12", 6,000 lb Legacy UFP disc brake applications 12" ventilated rotor with Zinc+ coating (5x the corrosion resistance of standard zinc plating) Aluminum caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Spacer bracket included for Dexter Axle mounting Kit includes all hardware: hex bolts, copper washers, banjo fitting Normalized SKU: K7181400UPC Code: 876983006434

Dexter Axle K71-815-00 Brake Components Stainless Ventilated Rotor With Aluminum Caliper Kit The Dexter Axle K71-815-00 is a complete disc brake kit pairing a 12" ventilated stainless steel rotor with an aluminum caliper, rated for 6,000 lb Legacy UFP axle applications. The aluminum caliper keeps things lighter than a full stainless setup while still delivering solid stopping performance for freshwater and moderate saltwater use. The 12" ventilated rotor is stainless steel, so the rotor itself holds up well against corrosion even in wet launch environments. The ventilated design helps dissipate heat during repeated brake applications, which is a real consideration when you're making multiple runs at the ramp in a day. Hardware throughout the kit is stainless where it counts: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless steel. Brake pads include a corrosion-resistant back plate. A spacer bracket is included specifically for mounting on a Dexter Axle, along with all necessary hardware to complete the installation. The kit ships with bracket, hex bolts, copper washers, banjo fitting, caliper, and rotor. Fits: 12", 6,000 lb Legacy UFP disc brake applications 12" ventilated stainless steel rotor Aluminum caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Spacer bracket included for Dexter Axle mounting Kit includes all hardware: hex bolts, copper washers, banjo fitting Normalized SKU: K7181500UPC Code: 876983006441

Dexter Axle K71-811-00 Brake Components Stainless Ventilated Rotor with Aluminum Caliper Kit The Dexter Axle K71-811-00 is a complete disc brake wheel kit built for 10.75", 3,750 lb Legacy UFP axle applications. It pairs a zinc-finished hub and stainless steel ventilated rotor with an aluminum caliper, making it a practical choice for lighter trailer setups where you want solid corrosion resistance without the cost of a full stainless caliper. The stainless rotor handles the wet environment well, and the ventilated design helps dissipate heat during repeated brake applications. The aluminum caliper keeps the overall kit cost down while still delivering reliable clamping force for the 3,750 lb rating. For freshwater trailers that see regular use, this combination hits a good balance between durability and value. Stainless steel is used throughout the hardware: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless. Brake pads include a corrosion-resistant back plate. A spacer bracket is included specifically for mounting on a Dexter Axle, along with all necessary hardware to complete the installation. The kit ships with bracket, hex bolt, copper washer, banjo fitting, caliper, and rotor. Fits: 10.75", 3,750 lb Legacy UFP disc brake applications 10.75" ventilated stainless steel rotor Zinc-finished hub Aluminum caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Spacer bracket included for Dexter Axle mounting Kit includes all hardware: hex bolt, copper washer, banjo fitting Normalized SKU: K7181100UPC Code: 876983006403

Dexter Axle K71-808-05 Brake Components Zinc+ Hub, Stainless Ventilated Rotor, and Stainless Caliper Kit The Dexter Axle K71-808-05 is a complete disc brake wheel end kit rated for 7,000 lb Legacy UFP axle applications. This is a full wheel end solution, not just a brake kit. It includes the hub, rotor, caliper, bearings, seals, and bearing protector, so you're getting everything needed to rebuild or upgrade a wheel end from the spindle out in one box. The hub carries a Zinc+ conversion coating, which delivers more than five times the corrosion resistance of standard zinc plating alone. The rotor is stainless steel and ventilated, handling both corrosion and heat management in environments where trailers get regular water exposure. The stainless caliper completes the corrosion-resistant package, making this kit well suited for saltwater or high-humidity use where lesser materials start showing their age quickly. Stainless steel runs throughout the hardware: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless. The bearing protector is stainless steel with a rubber bra cover to keep grease in and water out. Inner and outer bearings, seals, and all mounting hardware are included. The kit ships with bracket, cone nuts, hex bolts, copper washers, banjo fitting, bearing cones, seals, caliper, hub, rotor, wheel nuts, and hardware. Fits: 7,000 lb Legacy UFP disc brake applications Zinc+ coated hub (5x the corrosion resistance of standard zinc plating) Ventilated stainless steel rotor Stainless steel caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Stainless steel bearing protector with rubber bra cover Inner and outer bearing cones and seals included Wheel nuts and all mounting hardware included Normalized SKU: K7180805UPC Code: 876983006793

Dexter Axle K71-812-00 Brake Components Stainless Ventilated Rotor With Stainless Caliper Kit The Dexter Axle K71-812-00 is a complete disc brake wheel kit built for 10.75", 3,750 lb Legacy UFP axle applications. It's the go-to kit for lighter trailer setups where a smaller rotor diameter is the right fit, and it doesn't cut corners on corrosion protection to get there. The hub is zinc-finished, and the rotor is stainless steel, giving you a practical combination of corrosion resistance across both components. The stainless caliper rounds out the package, making this a solid choice for trailers that see regular water exposure. The ventilated rotor design helps manage heat during repeated brake applications, which matters any time you're making multiple launches in a session. Stainless steel is used throughout the hardware: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless. Brake pads include a corrosion-resistant back plate. A spacer bracket is included specifically for mounting on a Dexter Axle, along with all necessary hardware to complete the installation. The kit ships with a bracket, hex bolt, copper washer, banjo fitting, caliper, and rotor. Fits: 10.75", 3,750 lb Legacy UFP disc brake applications 10.75" ventilated stainless steel rotor Zinc-finished hub Stainless steel caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Spacer bracket included for Dexter Axle mounting Kit includes all hardware: hex bolt, copper washer, banjo fitting Normalized SKU: K7181200UPC Code: 876983006410

Dexter Axle K71-774-02 Brake Components Caliper Replacement Kit, RH, Zinc The Dexter Axle K71-774-02 is a right-hand caliper replacement kit for Legacy UFP disc brakes using the Special 8" disc application. If your right-side caliper is leaking, seized, or just worn out, this kit gets you back to a complete, functional brake setup without replacing the entire wheel end. The caliper is zinc-finished for corrosion resistance and comes as a complete assembly ready to install. The kit includes the caliper, bolts with threadlock coating, and copper washers. Bolts come pre-treated with threadlock coating, so you're not hunting for a tube of Loctite before you can button things up. This kit is specific to the right-hand (RH) side and the Special 8" disc configuration. Make sure your existing setup matches before ordering, as caliper kits for standard disc sizes, parking brake applications, and pre-2005 Old Style brakes are separate part numbers with different kit contents. Application: Legacy UFP disc brakes, Special 8" disc Side: Right-hand (RH) Caliper finish: Zinc Includes: Caliper assembly, bolts with threadlock coating, copper washers Note: Parking brake and pre-2005 Old Style kits are separate part numbers with additional contents Normalized SKU: K7177402UPC Code: 876983005796

Dexter Axle K71-807-05 Brake Components Zinc+ Hub, Stainless Ventilated Rotor, and Aluminum Caliper Kit The Dexter Axle K71-807-05 is a complete disc brake wheel end kit rated for 7,000 lb Legacy UFP axle applications. Like the K71-808-05, this is a full wheel end solution that includes the hub, rotor, caliper, bearings, seals, and bearing protector. The difference here is the aluminum caliper, which brings the cost down while keeping the same Zinc+ hub and stainless rotor combination. The hub carries a Zinc+ conversion coating, delivering more than five times the corrosion resistance of standard zinc plating alone. The rotor is stainless steel and ventilated, holding up well against corrosion and managing heat during repeated brake applications. The aluminum caliper is a solid fit for freshwater trailers and moderate saltwater exposure where the full stainless caliper isn't a requirement. Stainless steel runs throughout the hardware: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless. The bearing protector is stainless steel with a rubber bra cover. Inner and outer bearings, seals, and all mounting hardware are included. The kit ships with bracket, cone nuts, hex bolts, copper washers, banjo fitting, bearing cones, seals, caliper, hub, rotor, wheel nuts, and hardware. Fits: 7,000 lb Legacy UFP disc brake applications Zinc+ coated hub (5x the corrosion resistance of standard zinc plating) Ventilated stainless steel rotor Aluminum caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Stainless steel bearing protector with rubber bra cover Inner and outer bearing cones and seals included Wheel nuts and all mounting hardware included Normalized SKU: K7180705UPC Code: 876983006786

Dexter Axle K71-806-05 Brake Components Zinc+ Hub, Zinc+ Ventilated Rotor, and Aluminum Caliper Kit The Dexter Axle K71-806-05 is a complete disc brake wheel end kit rated for 7,000 lb Legacy UFP axle applications. It's the value-focused option in the 7,000 lb wheel end kit lineup, with both the hub and rotor carrying a Zinc+ conversion coating and an aluminum caliper rounding out the package. Zinc+ is a conversion coating applied over zinc plating that delivers more than five times the corrosion resistance of standard zinc plating alone. Having it on both the hub and rotor gives this kit solid protection for freshwater trailers and regular launch ramp use without the cost premium of stainless rotor or caliper components. The ventilated rotor design helps manage heat during repeated brake applications, keeping performance consistent across multiple runs. Even at this price point, the hardware doesn't cut corners: banjo bolt, bleeder screw, slider pins, and brake pad guides are all stainless steel. The bearing protector is stainless steel with a rubber bra cover to keep grease in and contaminants out. Inner and outer bearings, seals, and all mounting hardware are included. The kit ships with bracket, cone nuts, hex bolts, copper washers, banjo fitting, bearing cones, seals, caliper, hub, rotor, wheel nuts, and hardware. Fits: 7,000 lb Legacy UFP disc brake applications Zinc+ coated hub and rotor (5x the corrosion resistance of standard zinc plating) Ventilated Zinc+ rotor for heat management Aluminum caliper body with piston and bracket Stainless steel banjo bolt and bleeder screw Stainless steel slider pins and brake pad guides Corrosion-resistant back plate for brake pads Stainless steel bearing protector with rubber bra cover Inner and outer bearing cones and seals included Wheel nuts and all mounting hardware included Normalized SKU: K7180605UPC Code: 876983006779

Dexter Axle K71-774-01 Brake Components Caliper Replacement Kit, LH, Zinc The Dexter Axle K71-774-01 is a left-hand caliper replacement kit for Legacy UFP disc brakes using the Special 8" disc application. If your left-side caliper is leaking, seized, or worn out, this kit gets you back to a complete, functional brake setup without replacing the entire wheel end. The caliper is zinc-finished for corrosion resistance and comes as a complete assembly ready to install. The kit includes the caliper, bolts with threadlock coating, and copper washers. Bolts come pre-treated with threadlock coating, so there's no need to track down a tube of Loctite before you can finish the job. This kit is specific to the left-hand (LH) side and the Special 8" disc configuration. If you need the right-hand side, that's the K71-774-02. Make sure your existing setup matches before ordering, as caliper kits for standard disc sizes, parking brake applications, and pre-2005 Old Style brakes are separate part numbers with different kit contents. Application: Legacy UFP disc brakes, Special 8" disc Side: Left-hand (LH) Caliper finish: Zinc Includes: Caliper assembly, bolts with threadlock coating, copper washers Right-hand version: K71-774-02 Note: Parking brake and pre-2005 Old Style kits are separate part numbers with additional contents Normalized SKU: K7177401UPC Code: 876983005789

Load Rite 6018.10 Brake ComponentsSteel Brake Line Kit for Tri-Axle TrailerBrake Line Kit Complete with 14″ Flex Hose(s)Kit Includes: Quantity (4) 3/16″ Steel Brake Line – 18″ (SKU #1021.03) Quantity (2) 3/16″ Steel Brake Line Coil – 57″ (SKU #1021.05) Quantity (6) Brake Line Clip – Plated *(NOT Sold Separately, Online)* Quantity (1) Brake Line Union Tee – Brass (SKU #1021.13) Quantity (2) Brake Line Cross Union – Brass Quantity (3) 3/16″ Steel Brake Line Coil – 77″ (SKU #1021.18) Quantity (6) Brake Line – 14″ – Flex Hose (SKU #1021.26) Quantity (1) Brake Line Inverted Flare Union – 3/16″ Barrel *(NOT Sold Separately, Online)* Quantity (1) Brake Line – 240″ – Hardline *(NOT Sold Separately, Online)* *(For Use with Load Rite Tri-Axle Model Trailers)***Please note-picture is for reference only. Due to vendor changes, brake lines, coils, flex hoses, and hardlines may have different metal fittings. Normalized SKU: 601810

Load Rite 6017.10S Brake ComponentsStainless Steel Brake Line Kit for Tandem TrailerStainless Steel Brake-Line Kit Complete with 14″ Flex Hose(s)Kit Includes: Quantity (2) Brake Line Assembly – 18″ – SS *(NOT Sold Separately, Online)* Quantity (1) Brake Line Assembly – 57″ – SS *(NOT Sold Separately, Online)* Quantity (4) Brake Line Clip – Plated *(NOT Sold Separately, Online)* Quantity (1) Brake Line Union Tee – Brass (SKU #1021.13) Quantity (1) Brake Line Cross Union – Brass Quantity (2) Brake Line Assembly – 77″ – SS *(NOT Sold Separately, Online)* Quantity (4) Brake Line – 14″ – Flex Hose (SKU #1021.26) Quantity (1) Brake Line – 240″ – Hardline – SS *(NOT Sold Separately, Online)* *(For Use with Load Rite Tandem Axle Model Trailers)***Please note-picture is for reference only. Due to vendor changes flex hoses may have different metal fittings. Normalized SKU: 601710S

Load Rite 6016.10S Brake ComponentsStainless Steel Brake Line Kit - Single AxleStainless Steel Brake-Line Kit Complete with 14″ Stainless Steel Flex Hose(s)Kit Includes: Quantity (1) Brake Line Assembly – 18″ – SS *(NOT Sold Separately, Online)* Quantity (2) Brake Line Clip – Plated *(NOT Sold Separately, Online)* Quantity (1) Brake Line Union Tee – Brass (SKU #1021.13) Quantity (1) Brake Line Assembly – 77″ – SS *(NOT Sold Separately, Online)* Quantity (2) Brake Line – 14″ – Flex Hose (SKU #1021.26) Quantity (1) Brake Line – 240″ – Hardline – SS *(NOT Sold Separately, Online)* *(For Use on Load Rite Single Axle Model Trailer)***Please note-picture is for reference only. Due to vendor changes flex hoses, and hardlines may have different metal fittings. Normalized SKU: 601610S