Victron Energy SCC010015050R Battery ChargersBlueSolar MPPT Charge Controller - 75V - 15AMPFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Programming, real-time data and history display options - Color Control GX or other GX devices: see the Venus documents on our website. - A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed Normalized SKU: SCC010015050RUPC Code: SCC010015050

Download LiteratureVictron Energy SCC010020020 Battery ChargersBlueSolar PWM-Light Charge Controller - 12/24V - 20AMPFeatures: Load output with low battery voltage disconnect function. Lighting control function, one timer only.  Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.  Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Specifications:AFD = NONE Continuous Amperage = NONE Lockable = NONE Positions = NONENormalized SKU: SCC010020020UPC Code: 8719076025351Victron Energy SCC010020020 Literature Download Quick Reference Guide

Download LiteratureVictron Energy SCC010030020 Battery ChargersBlueSolar PWM-Light Charge Controller - 12/24V - 30AMPFeatures: Load output with low battery voltage disconnect function. Lighting control function, one timer only.  Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting.  Three stage battery charging (bulk, absorption, float), not programmable. Load output protected against over load and short circuit. Protected against reverse polarity connection of the solar array and/or battery. Day/night timing options: see manual for details Specifications:AFD = NONE Continuous Amperage = NONE Lockable = NONE Positions = NONENormalized SKU: SCC010030020UPC Code: 8719076025405Victron Energy SCC010030020 Literature Download Quick Reference Guide

Victron Energy CCH012100000 Battery ChargersCentaur Charger - 12 VDC - 100AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: CCH012100000UPC Code: 8719076021537

Victron Energy CCH012040000 Battery ChargersCentaur Charger - 12 VDC - 40AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Normalized SKU: CCH012040000UPC Code: CCH012040000

Victron Energy CCH012060000 Battery ChargersCentaur Charger - 12 VDC - 60AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Normalized SKU: CCH012060000UPC Code: CCH012060000

Victron Energy CCH012080000 Battery ChargersCentaur Charger - 12 VDC - 80AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Normalized SKU: CCH012080000UPC Code: CCH012080000

Victron Energy CCH024030000 Battery ChargersCentaur Charger - 24 VDC - 30AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Normalized SKU: CCH024030000UPC Code: CCH024030000

Victron Energy CCH024040000 Battery ChargersCentaur Charger - 24 VDC - 40AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: CCH024040000UPC Code: 8719076021568

Victron Energy CCH024060000 Battery ChargersCentaur Charger - 24 VDC - 60AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Normalized SKU: CCH024060000UPC Code: CCH024060000

Victron Energy PCH024016001 Battery Chargers The Victron Energy Phoenix PCH024016001 is a 24V, 16-amp two-bank battery charger built for serious marine and off-grid applications. It delivers 16 amps of total output across two banks, making it well suited for vessels running dual 24V battery banks or a combination of house and start batteries at 24V. This is not a trickle charger or a weekend warrior unit. It is a microprocessor-controlled charger designed to manage batteries intelligently over the long haul. The Phoenix uses an adaptive 4-stage charge cycle: bulk, absorption, float, and storage. Each stage serves a specific purpose in getting a battery fully charged and keeping it healthy between uses. The adaptive element is what sets it apart from basic chargers. The charger monitors how the battery is actually being used and adjusts the absorption phase accordingly. Shallow discharges get a shorter absorption time to avoid overcharging. Deep discharges trigger a longer absorption phase to ensure the battery comes back to a full state of charge. The charger does the thinking so you do not have to. The BatterySafe mode prevents damage from excessive gassing during high-current charging. When the battery reaches the gassing voltage threshold, the Phoenix automatically limits the rate of voltage increase rather than pushing through it. This protects battery plates and extends overall battery life, particularly important on AGM and gel batteries that are more sensitive to overcharge than flooded lead-acid. Storage mode activates automatically when the battery has not been discharged for 24 hours. In storage mode, float voltage drops to 2.2V per cell (13.2V on a 12V equivalent, 26.4V on a 24V bank) to minimize gassing and positive plate corrosion. Once per week the charger raises voltage back to absorption level to equalize the battery and prevent electrolyte stratification and sulfation, two of the leading causes of premature battery failure on boats that sit between seasons. Every Phoenix charger includes a battery temperature sensor. When connected, the charger automatically adjusts charge voltage based on battery temperature, which is particularly valuable for sealed batteries and installations where ambient temperature swings significantly between day and night or season to season. The voltage sense feature compensates for voltage drop across long cable runs, ensuring the battery receives the correct charge voltage regardless of resistance in the wiring between the charger and the battery terminals. Input voltage range is 90 to 265V AC, covering both North American 120V and European 240V shore power without any manual switching. The charger also accepts 90 to 400V DC input for DC-to-DC charging applications. It is ignition protected for safe installation in engine compartments and includes a computer interface for monitoring and configuration. Output: 16 amps total, 24V, 2-bank Charge stages: bulk, absorption, float, storage Input: 90-265V AC or 90-400V DC Includes battery temperature sensor BatterySafe mode for gassing protection Ignition protected Computer interface included Normalized SKU: PCH024016001

Victron Energy CCH012020000 Battery Chargers Centaur model 20 amp 12 volt below deck 3 bank battery charger by Victron Energy that provides 3-stage charging with temperature compensation. Victron Energy 3 bank 12 volt 20 amp battery charger for below deck installation Universal global AC input from 90 to 265 volts and either 50 or 60 Hz 3-stage charging profile with bulk, absorption, and float with temperature compensation DIP switch selectable for optimal charging voltage for flooded lead acid, gel, or AGM batteries Isolated charging outputs to 3 battery banks with each capable of full-rated output Epoxy powder-coated aluminum chassis with drip shield and stainless steel hardware Acrylic-coated circuit boards for maximum corrosion protection 5-year warranty Normalized SKU: CCH012020000

Victron Energy CCH012030000 Battery ChargersCentaur Charger - 30AMP, 12/30(3), 120-240VThe Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.The range spans 12V and 24V models from 16A through to 100A.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: CCH012030000UPC Code: 8719076021483

Victron Energy CCH012050000 Battery ChargersCentaur Charger - 50AMP, 12/50(3), 120-240VThe Centaur range of battery chargers features auto-ranging input covering 90-265VAC 50/60Hz input meaning they can be used anywhere in the world.Crucially, and unlike many other products that state universal input, the Centaur range will maintain full output power within the entire specified range. Other features include fully automatic three stage charge characteristic that ensures batteries are fully charged every time and three isolated charge outputs for multi battery configurations to suit the majority of typical installations.The range spans 12V and 24V models from 16A through to 100A.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Normalized SKU: CCH012050000UPC Code: 8719076021506

Victron Energy PMP122200102 Battery ChargersVictron Energy Multiplus 12/2000/80-50 120v UL 458 #PMP122200102Normalized SKU: PMP122200102

Victron Energy PMP122305102 Battery ChargersVictron Energy Multiplus-II 12/3000/120-50 2x120v UL #PMP122305102Normalized SKU: PMP122305102

Victron Energy ORI121221040 Battery Chargers For 12-volt dual-battery systems, delivering adjustable charging up to 70 amps with Bluetooth Smart, VE.Direct, smart alternator compatibility, and programmable charging profiles. The Victron Orion XS 12/12-70A is a high-performance DC-DC battery charger designed for 12-volt vehicle, marine, RV, and off-grid auxiliary battery systems. It is built for dual-battery installations charged from an intelligent alternator, helping ensure controlled charging of the service battery while protecting the starter battery from discharge. With adjustable charge current from 1 to 70 amps, programmable charging algorithms, and eight pre-programmed battery settings, the Orion XS 12/12-70 amp supports flexible installation across different battery types and system needs. Built-in Bluetooth Smart allows setup, monitoring, and software updates through the VictronConnect app, while VE.Direct enables wired integration with GX devices for advanced monitoring and control. This model is especially useful for Euro 5 and Euro 6 vehicles with smart alternators, where alternator voltage can be too low for reliable auxiliary battery charging. Engine shutdown detection activates charging only when alternator power is available. Key Features 12-volt input to 12-volt output DC-DC battery charger Adjustable charging current from 1 amp to 70 amps Output voltage adjustable from 10 volts to 17 volts Designed for dual-battery systems with intelligent alternators Smart alternator compatible with engine shutdown detection Adaptive 4-stage charge algorithm Fully programmable charging algorithms Eight pre-programmed battery settings Built-in Bluetooth Smart for VictronConnect setup and monitoring Instant Readout in VictronConnect for key data, warnings, and alarms VE.Smart Networking support for Vsense, Tsense, and Isense data VE.Direct port for wired GX device, PC, or other device connection DVCC support with compatible firmware and GX device Can be used as a power supply with output voltage set through VictronConnect Unlimited parallel connection capability to increase output current Screw terminal DC connections Technical Specifications Model: Orion XS 12/12-70 amps Product type: DC-DC battery charger Input voltage range: 9 volts to 17 volts Output voltage adjustment range: 10 volts to 17 volts Output voltage tolerance: ±0.25% maximum Output voltage noise: 10 mV rms Input and output current setting range: 1 amp to 70 amps Maximum constant short-circuit current: 70 amps Continuous output power up to 40°C: 1000 watts Maximum efficiency: 98.5% No-load current consumption: Less than 100 mA Standby current consumption: Less than 1.5 mA Operating temperature range: -20°C to +60°C Temperature derating: 1.5% per °C above 40°C Humidity: 95%, non-condensing Maximum altitude: 2000 m Pollution degree: PD2 Overvoltage category: OVC 1 DC connection: Screw terminals Maximum cable cross-section: 4 AWG, 25 mm² Weight: 0.340 kg, 0.74 pounds Dimensions H x W x D: 137.3 x 123.1 x 40 mm, 5.4 x 4.85 x 1.6 inches Protection category: IP20 Safety standard: IEC 62477-1 EMC standards: EN 300 328, EN 301 489-1, EN 301 489-17, FCC 15B, ICES-003 Automotive directive: ECE R10-7 Applications RV auxiliary battery charging Marine dual-battery systems Van and camper electrical systems 12-volt service battery charging from a 12-volt starter battery Smart alternator vehicle charging systems Mobile power systems with long cable runs or voltage drop concerns DC power supply applications where adjustable output voltage is required Ideal For Buyers needing a 70 amp DC-DC charger for a 12 volt auxiliary battery bank Vehicles with Euro 5 or Euro 6 smart alternators RV, van, and marine systems where alternator voltage may be insufficient Installations requiring app-based setup and monitoring Victron systems using VE.Direct, GX devices, or VE.Smart Networking Users who need scalable charging by connecting multiple units in parallel Protection Features Input undervoltage protection with configurable lockout and restart values Low-temperature shutdown to help protect lithium batteries Overload protection Short-circuit protection Excessive temperature protection Output power reduction when maximum product temperature is reached Starter/input battery protection against deep discharge Engine shutdown detection to prevent drawing power when the alternator is not supplying power System Compatibility Compatible with 12-volt input and 12-volt output battery systems Compatible with intelligent alternator systems Configurable through VictronConnect on Apple and Android smartphones, tablets, and other devices Supports VE.Smart Networking data from compatible devices such as BMV, SmartShunt, or Smart Battery Sense VE.Direct compatibility for connection to GX devices such as Cerbo GX or Ekrano GX DVCC compatibility requires Orion XS firmware v1.03 or later and Venus OS firmware v3.20 or later on the GX device Can receive Vsense, Tsense, and Isense data over VE.Smart Networking Synchronized charging is not supported Check Before Ordering Confirm your system is 12-volt input and 12-volt output; this model is not for 24-volt output systems Confirm the required charge current is appropriate for your auxiliary battery bank and wiring This 12/12-70 amp model is rated IP20 and is intended for dry indoor installation only Verify cable size, fuse protection, mounting location, airflow, and installation clearances before installation Continuous output power is based on optimal cooling and proper mounting; limited airflow may cause earlier current derating Confirm firmware requirements when using DVCC with a GX device For lithium battery systems, confirm BMS remote on/off or control requirements before installation Use VictronConnect to configure charge settings for the connected battery type Normalized SKU: ORI121221040UPC Code: 08719076075257

Victron Energy ORI242428120 Battery Chargers The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C. Normalized SKU: ORI242428120UPC Code: 8719076046097