(Mouse over to zoom - click to enlarge)
Attwood Gas Spring, 60 lb., Extended: 20", Compressed: 12" #SL34-60-5

Attwood Gas Spring, 60 lb., Extended: 20", Compressed: 12" #SL34-60-5

Manufacturer: Attwood Marine
Part Number: SL34-60-5
SKU: ATT-SL34-60-5
Share, print or email this page.
(click the plus for more options)
Regular Price: $21.99
On Sale For: $15.57

ITEM IS AVAILABLE


Quantity:   

Free Choice Shipping on most orders over $100More Info

Ni-Slide Series

Attwood gas springs are made with bio-degradable no hazzard to water grade oil (WGK), making them the marine industry’s most environmentlly friendly gas springs. All springs pass ASTM B117, Attwood salt spray and a 30,000 cycle lifecycle test. Attwood gas springs come has many configurations to fit your needs including: marine, industrial, agricultural, pharmacuetical, food processing, and medical. Available in 6mm, 8mm and 10mm configurations between 10 and 100 pound output force.

The Ni-Slide series carries Attwood’s widest selection of configurations and lengths. These gas springs are the industry’s proven leader in value, quality and durability.

Important Notice: Gas Spring Disposal
Do not discard oil-filled Gas Springs!

It is easy to drain this hydraulic oil and recycle it in the same manner as motor oil or transmission fluid.

Follow these instructions to remove the oil.

  1. Gas Springs are under pressure. Work carefully and wear eye protection!
  2. Clamp Gas Spring in a vise.
  3. Screen off the work area to deflect escaping gas and oil splashes. Have a container ready to collect oil.
  4. Use a 1/8" (3mm) drill bit to drill a hole 3/4" (20mm) from bottom end of the Gas Spring. Hole must be 3/8" (10mm) deep.
  5. Drain oil by pumping the piston rod in and out several times.
  6. Collect and dispose of the oil and Gas Spring according to local disposal and environmental regulations.
Product Rating: (0.00)   # of Ratings: 0   Rate It! Click Here to rate this product

There are no comments for this product. CLICK HERE to be the first one to share your opinion!
ATTWOOD LIMITED WARRANTY

Attwood Corporation, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”) warrants to the first consumer purchaser of its products that Attwood will replace or repair the product, at its sole discretion, if any defects in material or workmanship are reported within the applicable warranty periods set out below from the date of the first retail purchase, subject to the remedies, exclusions, and limitations in this Limited Warranty. This limited warranty is effective for all Attwood products purchased after May 1, 2008.

1. Boat Covers and Tops: *Attwood will apply the below percentages of the original purchase price of the boat cover as a discount off of the cost of a replacement boat cover for each of the prorated warranty periods set out below.

a. Silver Coat, Road Ready™ ,Snug Harbor Silver Series, and Custom Boat Covers: 3 years Prorated
From Purchase Date Discount* From Purchase Date Discount*
1st Full Year 100% 3rd Full Year 33%
2nd Full Year 67%
b. Road Max™ Boat Covers: 4 years Prorated
From Purchase Date Discount* From Purchase Date Discount*
1st Full Year 100% 3rd Full Year 50%
2nd Full Year 75% 4th Full Year 25%
c. Snug Harbor Titanium Series, Road Max™ 600 Boat Covers and Acrylic and Vinyl Bimini Tops: 5 years Prorated
From Purchase Date Discount* From Purchase Date Discount*
1st Full Year 100% 4th Full Year 40%
2nd Full Year 80% 5th Full Year 20%
3rd Full Year 60%
d. Boaters Best™ Boat Covers: 6 years Prorated
From Purchase Date Discount* From Purchase Date Discount*
1st Full Year 100% 4th Full Year 49%
2nd Full Year 83% 5th Full Year 32%
3rd Full Year 66% 6th Full Year 15%
e. Boaters Best™ Ultimate Boat Covers: 8 years Prorated
From Purchase Date Discount* From Purchase Date Discount*
1st Full Year 100% 5th Full Year 50%
2nd Full Year 88% 6th Full Year 37%
3rd Full Year 75% 7th Full Year 25%
4th Full Year 63% 8th Full Year 12%
2. Pumps:
a. Heavy Duty Bilge Pumps Installed on Recreational/Pleasure Boats (Part Numbers 4030,4040,4060,4070): 3 years
b. Heavy Duty Bilge Pumps Installed on Commercial Boats (Part Number 4030,4040,4060,4070): 1 year
c. V-Series Bilge Pumps (Part Numbers 4204, 4206, 4207, 4208, 4209, 4212, and 4224): 3 years
d. Sahara Series Automatic Bilge Pumps (Part Numbers 4505, 4507, 4508, 4511): 3 years
e. Tsunami Series Cartridge Bilge and Aerator Pumps (Part Numbers 4606, 4608, 4609, 4612, 4613, 4620, 4622, 4623, 4624, 4625, 4640, 4650, 4651, 4660, 4661, 4670, 4672): 3 years
3. Automatic Float Switch (Part Numbers 4201, 4202): 3 years
4. Electronic Bilge Switch (Part Numbers 4801, 4802): 3 years
5. Bilge Blowers:
a. Water-Resistant Turbo Bilge Blowers (Part Numbers 1733, 1743, and 1745): 3 years
b. Standard (Non Water-Resistant) Turbo Bilge Blowers (Part Numbers 1731 and 1741), except when used in applications which allow contact with liquids (Exception No. 2): 1 year
6. LED Lights: 10 years
7. 6 Gallon Gas Tank (Part Number 8867): 3 years
8. Pro-Series Rod Holders (Part Numbers 5002, 5003, and 5004): 5 years
9. ZAMAK Hardware, or Perma-Plate Parts: 2 years
10. Attwood Cast Stainless Steel Hardware: Life of the Boat
11. All other Attwood and Swivl-Eze Brand Products (subject to limitations below): 1 year

Statute of Limitations: Any action for rescission or revocation against Attwood shall be barred unless it is commenced within one (1) years from the date of accrual of such cause of action. This provision does not grant any consumer a right of rescission or revocation against Attwood, where such right does not otherwise exist under applicable law. Some states may not allow the applicable statute of limitations for rescission or revocation to be reduced, so this provision may not apply to each retail owner.

Other Limitations: EXCEPT AS SET FORTH HEREIN, THERE ARE NO OTHER WARRANTIES EITHER EXPRESS OR IMPLIED PROVIDED BY ATTWOOD ON THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE EXPRESSLY EXCLUDED. ATTWOOD FURTHER DISCLAIMS ANY LIABILITY FOR ECONOMIC LOSS ARISING FROM CLAIMS OF PRODUCT FAILURE, NEGLIGENCE, DEFECTIVE DESIGN, MANUFACTURING DEFECT, FAILURE TO WARN AND/OR INSTRUCT, LACK OF SEAWORTHINESS, AND ANY OTHER THEORY OF LIABILITY NOT EXPRESSLY COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY. TO THE EXTENT REQUIRED BY LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED FOR THE DURATION OF THE RESPECTIVE EXPRESS LIMITED WARRANTIES STATED HEREIN. TO THE EXTENT ALLOWED BY LAW NEITHER ATTWOOD, NOR THE SELLING DISTRIBUTOR SHALL HAVE ANY RESPONSIBILITY FOR LOSS OF USE OF THE PRODUCT OR THE BOAT, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT BE APPLICABLE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT BE APPLICABLE. THIS WARRANTY GIVES THE OWNER SPECIFIC LEGAL RIGHTS, AND THE OWNER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. RETAIL CUSTOMERS IN THE EUROPEAN ECONOMIC AREA (EEA) MAY HAVE LEGAL RIGHTS UNDER APPLICABLE NATIONAL LEGISLATION REGARDING THE SALE OF RETAIL GOODS WHICH ARE NOT AFFECTED BY THIS LIMITED WARRANTY. THE RETAIL CUSTOMER’S LEGAL RIGHTS UNDER ANY APPLICABLE NATIONAL LEGISLATION REGARDING THE SALE OF RETAIL GOODS SHALL NOT BE AFFECTED.

You can receive information relating to privacy and to this limited warranty in Europe on www.attwoodmarine.com and by contacting Attwood at the address listed on next page.

Sole Remedy: In no event shall any repair or replacement under this Limited Warranty exceed the fair market value of the product as of the date of the owner’s claim.

THE REMEDY OF REPAIR OR REPLACEMENT OF PARTS OR MATERIALS FOUND TO BE DEFECTIVE IN FACTORY MATERIALS OR WORKMANSHIP COVERED BY THIS LIMITED WARRANTY SHALL CONSTITUTE THE OWNER’S SOLE AND EXCLUSIVE REMEDY AGAINST ATTWOOD FOR ANY CLAIMS WHATSOEVER OF ECONOMIC LOSS RESULTING FROM PRODUCT FAILURE.

Acceptance of any product returned or any refund provided by Attwood shall not be deemed an admission that the product is defective. Products that are replaced become Attwood’s property. The terms and conditions contained in this limited warranty may not be modified, altered or waived by any action, inaction, or representations, whether oral or in writing, except upon the express, written authority of a management level employee of Attwood.

Exclusions: This Limited Warranty does not apply to the following items:

1. Any Attwood products used in other applications than on pleasure boats, including but not limited to non-marine use or use on boats which are utilized for racing or commercial purposes, with the exception of the Heavy Duty Bilge Pumps
installed on commercial boats (see 1b, above) (Part Numbers 4030,4040,4060,4070).

2. Any non water-resistant Turbo Bilge Blowers (Part Numbers 1731, and 1741) used in applications which allow direct contact with water or other liquids.

3. Due to wind velocity encountered when boats are trailered, only Snug Harbor™ Silver Series, Snug Harbor™ Titanium Series, Silver Coat, Road Ready™, Road Max™, Road Max™ 600, Boaters Best™, Boaters Best™ Ultimate, and Custom boat covers, when properly tied down, are warranted as suitable for use in connection with towing on a trailer. No warranty is extended on any other boat covers when used in connection with a trailered boat.

4. Damage to the boat cover or to any other property or any injury resulting from the failure to properly tie down a boat cover before towing is not covered.

5. Ancillary equipment used or associated with Attwood products, including but not limited to, batteries, fuses, electric light bulbs, lamps, or sealed beam units.

6. Any product damaged by accident, acts of nature, improper installation, unreasonable or improper use, lack of proper maintenance, unauthorized repairs or modifications, abuse, normal wear or tear, or other causes not arising from
defects in materials or workmanship.

7. Any expenses involved in the removal, reinstallation, or transportation of the product.

8. Any product damaged by the failure of the owner to use, maintain, or store the product as specified in any instructions.

9. Any boat cover torn or ripped because of forcing the fabric over sharp edges or corners, failing the protect the fabric from sharp objects, or allowing water, snow or ice to pool or puddle on the product.

10. Any boat cover fabric discoloration, or failure due to chemical exposure such as bird droppings, tree sap, gas, and oil or mildew due to water, snow or ice, dirt, leaves, pine needles resting on the product or the product stored while damp.

11. Any defect or repair requiring redesign of the Attwood product, except pursuant to the recall provisions of the United States Federal Boat Safety Act of 1971 or the recall laws of any other foreign jurisdiction.

Owner’s Obligations: It is the responsibility of the purchaser to return the product to Attwood at the address below, postage pre-paid, and insured with proof of original purchase including date.

Attwood Corporation
1016 North Monroe
Lowell, Michigan 49331

 
 From aerator pumps to ZAMAK lights, Attwood has thousands of superior-quality products to fit nearly every boat. First Choice Marine is one of the nations premier Attwood distributors and we carry a lot of the hard to find items that the discount store won't. We also handle a complete line of Swivl-Eze products as well, an Attwood brand. So if you need quality Attwood products, you have found your source.

Cockpit & InteriorAnchoringFuel SystemsBoat CoversBimini TopsMarine HardwareFishing AccessoriesVent and blowers





Flush Cleat, stainless steel, stud mount, 66512
Attwood 4-1/2" Flush Cleat, Stud Mount, Stainless Steel #66512-7

Great new Flush Cleat design from the leader in stainless steel hardware! This cleat recesses flush to the deck for a clean, contemporary look at an affordable price. Corrosion-resistant 316 stainless steel construction (patented design). Water-resistant cleat recesses into cast body, and is captured with lubricated seals. An optional drainage rec ... learn more

Regular Price 78.99
Sale Price 58.74
Available Quantity: 22
Part Number: 66512-7

ITEM IS AVAILABLE


Boss Audio MRANT12 12 inch Rubber AM/FM Antenna #MRANT12
Boss Audio MRANT12 12 inch Rubber AM/FM Antenna #MRANT12

MRANT12Marine Rubber Antenna ... learn more

Regular Price 10.99
Sale Price 7.16
Available Quantity: 100+
Part Number: MRANT12

ITEM IS AVAILABLE


Seasense 3/8 inch X 15' Double Braid Dock Line Nylon Black #50013092
Seasense 3/8 inch X 15' Double Braid Dock Line Nylon Black #50013092

Give your boat a sharp well-kept look with premium pre-spliced double braid nylon dock lines. Both the cover and the core are manufactured from the highest quality marine grade nylon giving you the strongest and easiest to handle line. Whipped on the splice & bitter end. ... learn more

Regular Price 10.99
Sale Price 7.25
Available Quantity: 2
Part Number: 50013092

ITEM IS AVAILABLE


Attwood Ball Stud 10mm 9/16" Shank L Stainless Steel #SL69SSBS-7
Attwood Ball Stud 10mm 9/16" Shank L Stainless Steel #SL69SSBS-7

Used as an alternative to mounting brackets, threaded studs can be mounted directly to hatches or other mounting surfaces that are made of metal or another material with the strength to withstand the forces of a gas-spring attachment point. ... learn more

Regular Price 8.99
Sale Price 5.63
Available Quantity: 21
Part Number: SL69SSBS-7

ITEM IS AVAILABLE


Attwood Gas Spring, 20 lb., Extended 7.5", Compressed 5.25" #SL31-20-5
Attwood Gas Spring, 20 lb., Extended 7.5", Compressed 5.25" #SL31-20-5

Ni-Slide SeriesAttwood gas springs are made with bio-degradable no hazzard to water grade oil (WGK), making them the marine industry’s most environmentlly friendly gas springs. All springs pass ASTM B117, Attwood salt spray and a 30,000 cycle lifecycle test. Attwood gas springs come has many configurations to fit your needs including: marine, indu ... learn more

Regular Price 21.99
Sale Price 15.57
Available Quantity: 19
Part Number: SL31-20-5

ITEM IS AVAILABLE


Attwood Gas Spring, 30 lb., Extended 7.5", Compressed 5.25" #SL31-30-5
Attwood Gas Spring, 30 lb., Extended 7.5", Compressed 5.25" #SL31-30-5

Ni-Slide SeriesAttwood gas springs are made with bio-degradable no hazzard to water grade oil (WGK), making them the marine industry’s most environmentlly friendly gas springs. All springs pass ASTM B117, Attwood salt spray and a 30,000 cycle lifecycle test. Attwood gas springs come has many configurations to fit your needs including: marine, indu ... learn more

Regular Price 21.99
Sale Price 15.57
Available Quantity: 23
Part Number: SL31-30-5

ITEM IS AVAILABLE


Attwood Gas Spring, 80 lb., Extended: 20", Compressed: 12" #SL34-80-5
Attwood Gas Spring, 80 lb., Extended: 20", Compressed: 12" #SL34-80-5

Ni-Slide SeriesAttwood gas springs are made with bio-degradable no hazzard to water grade oil (WGK), making them the marine industry’s most environmentlly friendly gas springs. All springs pass ASTM B117, Attwood salt spray and a 30,000 cycle lifecycle test. Attwood gas springs come has many configurations to fit your needs including: marine, indu ... learn more

Regular Price 21.99
Sale Price 15.81
Available Quantity: 0
Part Number: SL34-80-5

ITEM IS OUT OF STOCK - Usually Ships in 3-7 Days


Attwood 40 Series Bracket, Stainless Steel, Ball Pem #SL40SSP3-7
Attwood 40 Series Bracket, Stainless Steel, Ball Pem #SL40SSP3-7

Bracket-Forward Perm (Ball ONLY)-Stainless Steel-Ball 10 mm ... learn more

Regular Price 9.99
Sale Price 6.93
Available Quantity: 34
Part Number: SL40SSP3-7

ITEM IS AVAILABLE

Start a discussion about this product
comments powered by Disqus






Shop boat insurance



First Choice Marine is an Upfront Merchant on TheFind. Click for info.