Cook Manufacturing 50012 Motor PlatesAllows the motor to be mounted 5 inches higher than the standard mounting on the transom. It is a must for conversion from a prop to jet drive. Another application includes mounting the 5" vertical extension on the hydraulic Power-Lift to raise the motor higher on shallow running boats that are equipped with tunnel extensions.CMC 5 Vertical Extension #50012Normalized SKU: 50012UPC Code: 739697500127

Cook Manufacturing 55012 Motor PlatesConstructed of 6061 T6 extruded aluminum alloy fastened with 100% stainless steel. Provides 5" of slot adjustment at motor mounting bracket and 2-1/2" of adjustment at transom bracket. After height adjustment has been made, tighten the 4 bolts on the sides to 100 lbs to hold in place. 5-1/2" set-back.CMC 5 1/2 In Set Back Plate #55012Normalized SKU: 55012UPC Code: 739697550122

Cook Manufacturing 7493 Relays Relay A completely new wire assembly will work with all of the CMC jack plates and trim & tilts that we have been making since 1990. 7493: 12V 80-amp relay has a skirt, has replaced the 7312 relay, and will plug into the same socket. Will not plug into the socket that was designed for the 7122. Normalized SKU: 7493UPC Code: 739697074932

Cook Manufacturing 20032 Motor Plates Stop bolts from biting into the transom. Constructed of 6061 T6 extruded aluminum alloy. CMC Bottom Washer Plate #20032 Normalized SKU: 20032UPC Code: 739697200324

Cook Manufacturing 65302 Motor PlatesMade of 1/2" 6061 T6 alloy aluminum extrusions with stainless steel fasteners. Ideal for fresh or salt water use. Max. lifting capacity of 7853 lbs thrust. Easily lifts even a V-6 300hp max. motor at full throttle. Hydraulic actuator is fully accessible without removing the engine and is completely self-contained with its own fluid reservoir. Made of 100% non-ferrous material, impervious to saltwater and freshwater. Roller assembly features stainless steel 3/4" pin with aluminum-bronze alloy rollers. Rated for V-6 motors and smaller. Provides 5" of vertical travel with 1-1/2" of adjustment on motor bracket and 1-1/2" of adjustment on transom bracket for total 8" of possible adjustment.CMC PL-65HS w/o gauge 5.5 #65302Normalized SKU: 65302UPC Code: 739697653021

Cook Manufacturing 65301 Motor PlatesMade of 3/4" & 1/2" 6061 T6 alloy aluminum extrusions and fastened w/SS fasteners. Ideal for fresh or saltwater use. No welds or castings to break. Dependable self contained and water proof high speed hydraulic actuator has a max. Lifting capacity of 4417 pounds of thrust. You will have no problem lifting even a V6 300 hp max. Motor at full throttle. The hydraulic actuator is mounted inside the structure of the Power-Lft., yet it is fully accesible without removing the engine. There are no hoses to contain, nor will you have to contend with mounting a pump and reservoir inside your boat, as is the need with other transom jacks. The hydraulic actuator is completely self-contained with its own fluid reservoir (eliminate the need for hydraulic tank and hoses inside the boat). It contains a permanent magnet motor for more power and constant torque. The cylinder within the actuator has more lifting capacity than other transom jacks on the market. It contains a no-leak sealand wiper that keeps dirt and wNormalized SKU: 65301UPC Code: 739697653014

Cook Manufacturing 70012 Motor PlatesCMC Marine Static Set-Back Plate 7" #70012Normalized SKU: 70012UPC Code: 739697700121

Cook Manufacturing 20022 Motor Plates Stop bolts from biting into transom Constructed of 6061 T6 extruded aluminum alloy Hole centers 12-7/8" Normalized SKU: 20022UPC Code: 739697200225

Cook Manufacturing 20122 Motor PlatesIs your boat planing even at low speed? Are you having a problem with your transom angle? The flexibility of the boat's trimming ability is mostly determined by the transom angles. Trimming in, trimming out, and trimming down are all concepts that a new boater should know. Each of them has a distinct impact on the boat's performance. Good thing we have the CMC WEDGES 2 DEGREE. These two-degree wedges are specially made to provide additional +/- trim. The wedges help boats with not enough transom angle or low-speed planing. By simply inverting 2, 4, and 6 sets, the CMC Transom Wedges' unusual shape allows you to utilize them as setback spacers. The hole pattern matches the Power-Lift transom bracket and standard motoring installation patterns. Key Features: Help boats with a low-speed planing issue or with an inadequate transom angle. The CMC Transom Wedges' unique design allows you to utilize them as setback spacers as well. These 2 wedges are designed to give extra positive or negative trim. The wedges are used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed. Unique design of transom wedges allows you to also use them as set back spacers, by simply inverting 2, 4 and 6 sets. Hole design fits the same pattern as the Power-Lift transom bracket and standard motoring mounting. Sold in pairs. Dimensions: 1/2" x 4" x 11 1/4"This product replaces:739697201222, 30-603, 20122Normalized SKU: 20122UPC Code: 739697201222

Cook Manufacturing 90012 Motor Plates The 9" Static Set Back Plate also has 1-1/2" of adjustment at the transom bracket and 1" of adjustment on the motor bracket. The dimension from the top of the transom to the top of the motor side is 5-3/4". Rated for V-6 and smaller motors Mounting hardware included Normalized SKU: 90012UPC Code: 739697900125

Cook Manufacturing 65012 Motor BracketsMade of 6061 T6 extruded aluminum alloy and fastened with stainless steel fasteners. It utilizes an all thread stainless steel screw centrally located for uniform lift and positive alignment. The motor bracket moves up and down on the transom bracket by use of rollers matched from aluminum-bronze alloy (same as hydraulic CMC Power-Lift). There is 5" of verticle adjustment, with a choice of 5-1/2" or 10" set back from transom. Designed to fit any standard motor up thru V-6, 300HP without drilling holes or making modifications. The Power-Lift provides the added convenience of adjusting from the top or the bottom.Cook Manufacturing Manual Transom Jack ML-65 65012Normalized SKU: 65012UPC Code: 739697650129

Cook Manufacturing 13003 Motor PlatesDesigned for boats used in shallow, stumpy areas. Rated for outboard motors up to 130 HP. Mounts between boat transom and motor, designed to help minimize damage to motor and boat transom only when an obstruction is encountered while running at speeds under 5 M.P.H in the forward direction. Not designed to encounter obstructions while the boat is being operated in reverse direction. Pre-drilled with standard BIA hole pattern. For motors using clamps with thumb screws, CMC part #13022 Transom Clamp Adapter is required.CMC BA130 JACK PLATE MANUAL #13003Normalized SKU: 13003UPC Code: 739697130034

Cook Manufacturing 13002 Tilt & Trim Rated for 130 hp and smaller motors, the 13002 will trim the motor 20° and a total of 65° of trim and tilt. It is actuated with a totally waterproof marine electric hydraulic system that is rated over 7800 lbs. of thrust! This hydraulic system is made of 100% non-ferrous materials which makes it more impervious to saltwater and freshwater than ball screw, electro-mechanical systems equipped on other brands. In fact, it is over twice as powerful as the ball screw electro mechanical actuator. The CMC hydraulic system is completely sealed and submersible and runs without worry of water damage. It is constructed of 1/2" 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners for maximum strength and durability. No welds or castings to break. Carry's a 5-year structure warranty. Unit incorporates a 6" set back which enhances boat stability and will put the prop in "cleaner" water, thus giving the prop a better "bite" and eliminating prop slippage. It can also increase top end speed and fuel efficiency. It is great for pontoon boats, too! Since access to the motor on most pontoon boats is very difficult, the 13002 can make it very convenient. It is back saving, and prop saving, simply by flicking a switch when approaching shallow water.  Features Rated for 130 H.P. and Smaller Motors 6" Set Back to Enhance Boat Stability and Performance 20° of Trim and a Total of 90° of Tilt and Trim 1/2" 6061 T6 Extruded Aluminum Construction with Stainless Steel Fasteners Electric Hydraulic Actuator Rated at 7853 lbs. of Thrust! Standard B.I.A. Bolt Hole Pattern Convenient Adapter Kit Available for Clamp-on Motors Four Stainless Steel Motor Mounting Bolts Included With the Electric Hydraulic Tilt & Trim you get power tilt & trim, better boat handling, more speed, lower fuel consumption and no more back strain! Specs Power Rating: Up to 130 HP Set Back: 6" Trim: 20° Tilt: 90° Material: 1/2" 6061 T6 Extruded Aluminum Bolt Hole Pattern: Standard B.I.A. Actuator Rating: 7853 lbs. of Thrust Note: clamp-on motors need an adapter (13002).Outboard: Trim Assembly Normalized SKU: 13002UPC Code: 739697130027